Votos - 0, Puntuación media: 0 ( )

Fabricar: Bosch Tamaño del archivo: 2.35 mb Nombre del archivo: Idioma del manual:

Only customer service may maintain, remove and install the float. You will need to purchase the following before using the dishwasher for the first time: – special salt for use in dishwashers – detergent – rinse-aid Only use products, which are suitable for dishwashers. en Water softener In order to rinse dishes and glasses satisfactorily, the dishwasher requires soft water, i.e. containing little or no lime, otherwise water stains will be left behind on crockery and glasses, etc. If the tap water exceeds a certain level of hardness, it must be softened, i.e. decalcified, so that it can be used in the dishwasher. This is achieved by adding a special salt to the water softener inside the dishwasher. The water softener, that is the required amount of salt, is set up according to how hard the tap water is. Setting up the water softener Determine the level of hardness of your tap water. Your local water company or service agent can help you with this. Identify setting from the following water hardness table. Close the door Rotate the programme selector 3 from the 12 o’clock position by one notch to the left. Water hardness table Switch on main switch 1 and hold down for at least 3 sec. The display 9 flashes and the lamps above the symbols and light up. (hardness value has been set to 2 at the factory). To change the setting: Rotate the programme selector 3 . You can select a set value between 0 and 3 according to the hardness of your water. If the lamps , and light up, the maximum set hardness value has been reached. If the set hardness value is now increased again, the lamps go out and the set hardness value is set to 0 (no lamp lights up). Switch off the main switch 1 . The chosen setting has now been stored. dh fH Clarke mmol/l 0–6 0–11 0–8 0–1,1 0 7–16 12–29 9–20 1,2–2,9 1 17–21 30–37 21–26 3,0–3,7 2 22–35 38–62 27–44 3,8–6,2 3 en Filling the salt dispenser Salt must always be filled before the appliance is switched on, so that excess salt solution is immediately flushed away to prevent corrosion. Open the screw-type cap of the compartment 27 . Before using the appliance for the first time, pour about 1 litre of water in the salt container. Then refill with salt (not cooking salt) until the salt container is full (max. 1.5 kg). When you refill the salt, water is being displaced and drains off. Warning Do not pour detergent into the container for special salt. This would destroy the water softener. Salt refill indicator As soon as the salt refill indicator 9 is lit on the control panel, refill with salt immediately before the next rinse cycle. Depending on the washing frequency and the hardness setting, the regeneration salt may not have to be topped up for several months. The LOW SALT indicator 9 on the front panel will light up initially but will extinguish again after a short period when the salt solution has become sufficiently concentrated. If the set hardness value is ”0”, do not add salt because no salt is used during operation; the salt refill indicator is switched off. en Adding rinse aid The rinse aid is required for stain-free utensils and clear glasses. Use only rinse aid for domestic dishwashers. Open the cover on the rinse-aid dispenser 30 . To do this, press the mark (1 ) on the cover and simultaneously lift the cover on the control plate (2 ). Adjusting the amount of rinse-aid The amount of rinse-aid added to the water can be varied by adjusting the stepless control. The rinse-aid control has been set to ”4” in the factory. Do not alter the setting of the rinse-aid control unless streaks (turn knob towards ”–”) or water marks (turn knob towards ”+”) are left on the dishes. 30 Close the lid, ensuring that you hear it snap closed. To prevent excessive foam formation during the next rinse cycle, remove any rinse aid which has run over with a cloth. Carefully pour in the rinse aid to just Rinse aid controller below the edge of the filler opening. Rinse-aid refill indicator As soon as the rinse-aid refill indicator lights up on the control panel 8 , refill with rinse aid. en Utensils Not suitable Cutlery and utensils made of wood. Fragile decorative glasses, hand-crafted and antique utensils. These decorative items are not dishwasher-proof. Plastic parts sensitive to hot water. Copper and tin utensils. Utensils which are soiled with ash, wax, lubricating grease or ink. Absorbent materials such as sponges and cloths. Aluminium and silver parts have a tendency to discolour and fade during the wash cycle. Even some types of glass (e.g. crystal glass objects) may turn cloudy after many wash cycles. Recommendation: In future buy utensils which are identified as dishwasher-proof. Damage to glassware and other dishes Possible causes: type of glass or manufacturing process chemical composition of detergent water temperature and duration of dishwasher programme. Suggested remedy: Use glassware or porcelain dishes that have been marked ’dishwasher–proof’ by the manufacturer. Use a mild detergent that is des...

Descargar ahora

Introduzca dos números de la imagen: