Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
No other settings on the appliance are required. Salt is still required if the water hardness is above 21 dH (37 fH, 26Clarke, 3.7 mmol/l). Fill the salt dispenser with salt 27 and select setting 6 on the water softening system. If in doubt, please contact the detergent manufacturer, especially if: the utensils are very wet at the end of the programme. limescale forms. en Note Optimum rinsing and drying results can be obtained by using standard detergents in conjunction with separate application of salt and rinse aid. Observance of the operating instructions or information on the packaging of the combined detergents determines their effectiveness. Note Even if the rinse aid and/or salt refill indicator is lit, the rinse programme runs correctly when 3in1 products are used. If the rinse aid refill indicator 7 or salt refill 6 indicator is defective and you would like to switch it off, proceed as follows: Switching the rinse aid refill indicator off and on You can switch the rinse aid refill indicator 7 on or off. This function can be changed as follows. Close the door. Hold down the programme button C and press the main switch 1 until the digital display lights up, then release the buttons. 3 is indicated on the digital display (rinse aid refill indicator on). By pressing the programme button C , you can switch off or switch on the rinse aid indicator. Switch off the main switch 1 ; the setting is saved. Switching the salt refill indicator / water softening system off and on Close the door. Hold down the programme button B and switch on the main switch 1 , then release the buttons. The illuminated button B and the factory-set value on the digital display flash. To change the setting: press the programme button B . Each time the button is pressed, the set value increases by one; when the value is reached, the display jumps back to (the salt refill indicator / water softening system has been switched off). Switch off the main switch 1 . The set value is stored within the device. Approx. 4 litres of water are required to regenerate the water softening system. As a result, the water consumption per rinse cycle increases by 0 to maximum 4 litres depending on the water hardness setting. Note If you use the detergent and rinse aid separately or switch from combined detergents to standard cleaning products, ensure that the rinse aid refill indicator has been switched on and the water softening system has been set to the correct water hardness. en Overview of programmes The max. possible number of programmes is illustrated in this overview. The corresponding programmes for your appliance can be found on the fascia. Coffee, cake, milk, sausage, cold drinks, salads Soups, souffles, potatoes, pastries, rice, eggs, fried food Delicate Type of Dishes e.g. porcelain, pans, cutlery, glasses, etc. Type of food remnants e.g. Programme- sequence Dry Clean 55 Clean 40 Prerinse Clean 55 Clean 45 Soups, potatoes, pastries, rice, eggs, fried food Wash programme Very little Amount of food remnants State of food remnant Intensive 70 Eco 50 Gentle 40 Quick 45 Prerinse Mixed Dry Clean 65 Clean 50 Prerinse Dry Clean 70 Clean 70 Prerinse 40 Prerinse Rinse off if the dishes have been stacked for several days in the dishwash er prior to washing. Inter- mediate rinse Inter- mediate rinse Inter- mediate rinse Inter- mediate rinse LittleLarge MixedNon- sensitive Lightly AdhesiveVery adhesive Dry Clean 70 Inter- mediate rinse Clean 65 Prerinse Inter- mediate rinse Normal 65 Programme selection with the details contained in the programme overview. The most appropriate programme can be identified by comparing the type of crockery, cutlery, etc., as well as the You will find the appropriate programme information in the introduction. amount and condition of food remains, en Washing dishes Reduce costs! If only a small number of dishes have been loaded into the dishwasher, selecting a programme that operates at the next lowest temperature will usually suffice. Programme specifications The programme specifications can be found in the summary of instructions. Programme specifications refer to normal conditions. Greater deviations may occur due to: varying amounts of dishes water supply temperature water pipe pressure ambient temperature mains voltage tolerances and the tolerances specific to the appliance (e.g. temperature, amount of water, etc.) The water consumption values refer to a set water hardness value of 4. Switching the dishwasher ON Turn on the tap. Set main switch 1 to ON. Indicators light up according to the last programme that was selected. This same programme will run again if no other programme button 9 is pressed. The numerical display 3 shows the expected duration of the programme. The programme starts automatically. Remaining running time display When the appliance has started, the expected programme running time is displayed. The programmed running time is affected by the water temperature, the number of dishes, as well as the de...
Otros modelos de este manual:Lavavajillas - 4VS740BP/31 (2.48 mb)