Votos - 2, Puntuación media: 3
(
)
)
|
Resumen del manual
Note to Installer – Be sure to leave these instructions for the and local Insp spspe eec ccto totor rr sin .use. Note to Consumer Keep these instructions with your Owner`s Manual for future reference. Skill level — Installation of this dishwasher requires basic mechanical ,Plumbing and electrical skills. Proper installation is the responsibility of the installer . Product failure due to improper installation is not covered under the Dishwasher Warranty Completion Time ? 1 to 3 Hours. New installations require more time than replacement installations. Built-In Dishwasher IMPORTANT The dishwasher MUST be installed to allow for future removal from the enclosure if service is required. If you received a damaged dishwasher , you should immediately contact your dealer or builder . FOR YOUR SAFETY Read and observe all CAUTIONS and WARNINGS shown throughout these instructions. While performing installations described in this booklet, gloves, safety glasses or goggles should be worn. WARNING To reduce the risk of electrical shock, fire, or injury to persons, the installer must ensure that the dishwasher is completely enclosed at the time of installation. READ CAREFULLY. KEEP THESE INSTRUCTIONS. 206C1559P148 31-30207 03-10 FL Installation Preparation PARTS SUPPLIED: Two #8 Phillips flat head wood screws, 5/8" long to secure dishwasher to underside of countertop (in literature package). MA TERIALS YOU WILL NEED : Ferrule, compression nut and 90°Elbow (3/8"NPT external thread on one end, opposite end sized to fit water supply) Thread seal tape UL Listed wire nuts (3) Materials For New Installations Only: Air gap for drain hose, if required Waste tee for house plumbing, if applicable Electrical cable or power cord, if applicable Screw type hose clamps Strain relief for electrical connection. Hand shut-off valve Water line 3/8" min. copper Coupler for extending drain line, if applicable TOOLS YOU WILL NEED: Phillips head screwdriver 5/16" and 1/4" nutdriver 6" Adjustable wrench Level Carpenters square Measuring tape Safety glasses Flashlight Bucket to catch water when flushing the line Gloves For New Installations Only: Tubing cutter Drill and appropriate bits Hole saw set Elbow, Ferrule and Compression Nut Wire Nuts (3) Waste Tee Electrical Cable (or Power Cord, if applicable) Hot Water line Screw Type Hose Clamps Coupler Hand Shut-Off Valve 2 Wood Screws Hole Saw Set Measuring Tape Tubing Cutter Drill and Bits Phillips Head Screwdriver 1/4" and 5/16" Nutdriver Safety Glasses 6" Adjustable Wrench Bucket Flashlight Gloves Carpenters Square Level 2 Thread Seal Tape Air Gap Strain Relief 90° Installation Preparation PREPARE DISHW ASHER ENCLOSURE Figure 1 4 6 Cabinets Square and Plumb Floor MUST be Even with Room Floor. Plumbing and Electric Service Must Enter Shaded Area 32-1/2to 35" Underside of Countertop to Floor 24" Min. The rough cabinet opening must be at least 24"deep and 23-5/8"To24" Wide. The opening should be to 35"max. height. DRAIN REQUIREMENTS Follow local codes and ordinances. Do not exceed 10 feet distance to drain. Do not connect drain lines from other devices to the dishwasher drain hose. Dishwasher must be connected to waste line with an air gap (not supplied) or 32" minimum high drain loop, depending on local codes and ordinances to prevent back flow into the dishwasher . ?Air gap must be used if waste tee or disposer connection is less than 18"above the floor to prevent siphoning. DRAIN PREPARATION The type of drain installation depends on answers to the following questions: Do local codes or ordinances require an air gap? Will waste tee or disposer connection be less than 18"above the floor? Will installation have a drain loop less than 32" above floor? If the answer to ANY of the 3 questions above is YES, Method 1 MUST be used . Otherwise either Method 1 or Method 2 may be used. Figure 3 or Figure 4. CAUTION: An air gap MUST BE USED if the drain hose is connected to waste tee or disposer lower than 18"above the floor. Failure to provide the proper drain connection height with air gap or 32" minimum, high drain loop will result in improper draining of the dishwasher . The dishwasher must be installed so that drain hose is no more than 10 feet in length for proper drainage. The dishwasher must be fully enclosed on the top, sides and back, and must not support any part of the enclosure. CLEARANCES: When installed into a corner , allow 2" min. clearance between dishwasher and adjacent cabinet, wall or other appliances. Allow 25-5/8"min. clearance from the front of the dishwasher for door opening. Figure 2 Figure 2 Clearancefor Door Opening2" Minimum Countertop Dishwasher 25-5/8" Method 1 Air Gap with Waste Tee or Disposer Figure 3 Method 2 High Drain with Waste Tee or Disposer Provide a method to attach drain hose to underside of countertop. 32" Min. 32" Min. 18" Min. 18" Min. Figure 4 Install waste tee or disposer and air gap according to m facturer instructions. Ma aan nnu uufacturer s’ CABINET PREPAR...