Votos - 4, Puntuación media: 4.5
(
)
)
|
Resumen del manual
For an ionisation smoke alarm, the system includes the Ei173 control panel, Ei174 vibrating pad and Ei151TL ionisation smoke alarm (with Ei172 pattress) and has the part number Ei170. For an optical smoke alarm version the Ei151TL is replaced with an Ei156TL optical smoke alarm, and the part number is Ei171 The Ei173 control panel includes a high intensity Xenon strobe, a sealed lead-acid rechargeable battery for standby use in the event of mains failure and all the required circuitry to connect to the smoke alarm and Ei174 vibrating pad The Ei173 control panel also incorporates a Test button and circuitry to continuously monitor the system wiring The Ei174 vibrating pad is designed to be placed under the mattress or pillow to wake people who fail to respond to the strobe alarm Up to 11 other smoke/heat alarms can be interconnected to the master smoke alarm. In the event of mains failure the rechargeable battery in the panel will power the system for one week. Operation The green indicator will illuminate to show mains power is present The red indicator will flash once every second to show that the mains supply is off and the system is running on battery backup power The red indicator will go off as the battery becomes depleted (with mains off) The slide switch on the control panel disconnects mains and battery power from the control panel and extinguishes both LED indicators The “Test” button will check the strobe, vibration pad and panel When the smoke alarm is activated, the Ei173 control panel will flash the strobe at 1Hz and activate the vibrating pad The interconnect wiring from the smoke alarm to the control panel is monitored so that if the smoke alarm is not connected or if it is open/short circuit, then the strobe will flash and the vibrating pad will turn on An auxiliary socket allows the connection of an extra strobe or vibrating pad Shannon Free Zone, Shannon, Co. Clare, Ireland. Ph.+353 61 471277 Fx.+353 61 471053 Email. eielectronics@eiltd.ie Web: E & OE As our policy is one of continuous product development, we reserve the right to alter product details without prior notice. Ei169 DataSht RevA Model Ei169 Technical Specification Sensor Optical or Ionisation Sensitivity: Complies with BS 5446 Part 1: 2000 Source: Americium 241 (for Ei171 only) Airspeed: Essentially immune to the effect of airspeed. Button Test: Tests strobe, vibration pad and panel Fault Monitor: Open/short circuit Supply Voltage: 230V AC Battery back up: Sealed Rechargeable lead acid battery Auxiliary socket: Provides 12V/200mA in alarm Placement Information Alarms should be placed in accordance with the general guidelines shown in the diagram above. These recommendations are based on the problem of areas of “dead air” close to corners of rooms and apexes of ceilings, which could result in the prevention of smoke reaching the smoke detector Power-On Indicator: Alarm: Temperature Range: Humidity Range: Interconnect: Fixing: Plastic material: Warranty: Approvals: Specifications are subject to change Continuous green LED Xenon tube strobe (1Hz) 0 to 40°C 0% to 90% Relative Humidity Up to 12 interconnected Ei151/154/156 smoke/heat alarms Screw fixings supplied UL94VO flame retardant 5 year (limited) warranty BS 415:1990 electrical safety Important Precaution: Do not install the actual smoke/heat alarm itself in new or renovated buildings until all work is completed (including floor coverings) and the building has been fully cleaned. The wiring can be installed when appropriate. (Excessive dust and debris from building work can contaminate the smoke chamber and cause problems, and it will also invalidate the guarantee). If it must be installed, cover it completely, particularly around the edges, with a dust cover (eg. a plastic bag), until all cleaning is finished.. Connect wires to the unit as in wiring diagram. All wiring must comply with local codes. Shannon Free Zone, Shannon, Co. Clare, Ireland. Ph.+353 61 471277 Fx.+353 61 471053 Email. eielectronics@eiltd.ie Web: E & OE As our policy is one of continuous product development, we reserve the right to alter product details without prior notice. Ei169 Data...