Votos - 2, Puntuación media: 3
(
)
)
|
Resumen del manual
Indicate escape routes for each room. Keep these routes free from obstruction and post copies of the escape routes in every room. 4. Make sure that all bedroom doors are shut while you are asleep. This will prevent deadly smoke from entering while you escape. 5. Try the door. If the door is hot, check your alternate escape route. If cool, open it cautiously. Be prepared to slam the door if smoke or 6. In smoky areas, crawl close to floor, hold your breath, and/or cover nose with a wet cloth. 7. Escape quickly; don't panic. 8. Establish a common meeting place outdoors, away everyone can meet and then take steps to contact those missing. Choose someone to assure that — many die going back –35– Taking Care of Your System Silencing Low Battery Warning Tones at the Touchpad Replacing Batteries in Wireless Sensors Wireless sensors may not have been used in your security system MAINTAINING YOUR SYSTEM The components of your security system are designed to be as maintenance-free as possible. However, to make sure that your system is in reliable working condition. 1. Test your system weekly. 2. Test your system after any alarm occurs (see TESTING THE SYSTEM). You can silence the touchpad’s warning tones by pressing the OFF key, but the touchpad's low battery message display will remain on as a reminder that you have a low battery condition one or more of your sensors. When you replace the weak battery with a fresh one, the sensor will send a "good battery" signal to the control as soon as the sensor is activated (opening/closing of door, window, etc.), causing the low battery display to turn off. If the is not activated, the display will automatically clear within approximately 1 hour. Each wireless sensor in your system has a 9-volt or 3-volt battery. The system battery in any wireless sensor, including smoke detectors, the optional personal transmitter, and the optional portable wireless touchpad. (A low battery touchpad is detected as soon as one of its keys is pressed, and the wired “ 00”.) Alkaline batteries provide a minimum of 1 year of operation, and provide 2–4 years of service. 3-volt lithium batteries provide Actual battery life will depend on the environment in which signals that the transmitter in the sensor has had to send, Factors such as humidity, high or low temperatures to the reduction of actual battery life in an installation. If you have a low battery in a wireless sensor, low battery message is displayed on the touchpad. – 36 – MAINTAINING YOUR SYSTEM (Continued) In addition, a battery-operated smoke detector with a low battery also emits a single "chirp" sound approximately once every 20–30 seconds, identifying itself as the smoke detector with the weak battery. Note: The low battery message comes on as a warning that battery replacement in indicated sensor(s) is due within 30 days. In the meantime, a sensor causing a low battery indication is still fully operational. Important: Use only batteries recommended by your installer as replacement. Routine Care • Treat the components of your security system as you would any other electrical equipment. Do not slam sensor-protected doors or windows. • Keep dust from accumulating on the touchpad and all protective sensors, particularly motion sensors and smoke detectors. • The touchpad and sensors should be cleaned carefully with a dry soft cloth. Do not spray water or any other fluid on the units. – 37 – QUICK GUIDE TO SYSTEM FUNCTION S FUNCTION PROCEDURE COMMENTS Check Zones Press READY key. To view faulted zones when system not ready. Arm System Enter code. Press arming key desired: (AWAY, STAY, INSTANT) Arms system in mode selected. Quick Arm (if programmed) Press #. Press arming key desired: (AWAY, STAY, INSTANT) Arms system in mode selected, quickly and without use of code. Bypass Zone(s) Enter code. Press BYPASS key. Enter zone number(s) to be bypassed (use 2-digit entries). Bypassed zones are unprotected and will not cause an alarm if violated. Quick Bypass (if programmed) Enter code. Press BYPASS key. Bypasses all faulted zones automatically. Silence Sounders Burglary: Fire: "Check": Enter code. Press OFF key. Press OFF key. Press any key. Also disarms system. Memory of alarm remains until cleared. Memory of Alarm remains until cleared. Determine cause. Disarm System Enter code. Press OFF key. Also silences sounders. Memory of alarm remains until cleared. Clear Alarm Memory After disarming, enter code again. Press OFF key again. Touchpad will beep rapidly upon entry if alarm has occurred. Alarm display will remain upon disarming until cleared. Duress (if active and connected to Customer Care Center) Arm or disarm "normally", but use your 4-digit Duress code to do so. Performs desired action and sends silent alarm to Customer Care Center. Panic Alarms (as programmed) Press key [A], [B], or [C] for at least 2 seconds. See the PANIC KEYS section for functions programmed for your system. Keys “A” and “B” may have been programmed for single-button ...
Otros modelos de este manual:Detector de incendios - SAVS20ADTG (250.13 kb)
Detector de incendios - Safewatch Pro 2000 (250.13 kb)