Votos - 1, Puntuación media: 4
(
)
)
|
Resumen del manual
1. General and function 3 2. Intended use 4 3. Safety- and maintenance- references 4 4. Installation places 4 5. Installation 5 6. Registering the smoke detector with the SC9000 base station of the SafeGuard / TotalGuard 5 7. Registering the smoke detector with the base stations of the types MS9470, MS9770, MS9970, SC2200, SC2700, SC2800, Protector 28 6 8. Registering the smoke detector with the base station of the type Homeguard MS8000 6 9. Changing the address of the smoke detector 7 10. Final assembly 8 11. Changing the battery 8 12. Frequently Asked Questions 8 13. Technical data 8 1 GENERAL INFORMATION AND FUNCTION The smoke detector can detect incipient low temperature fires and open fires with smoke development and can be installed in any room. The smoke detector operates by the optical principle. There are no radioactive substances in this detector. The smoke detector incorporates the following features: • It monitors rooms for the development of smoke. • It has an integrated signal transmitter. • Your Marmitek Alarm System dials out, even if your security system is not armed. 2 INTENDED USE The radio smoke detector is intended for the detection of smoke in interiors by the use of optical and acoustic warnings, as well as wireless transmission over distances of up to 30 meters. In combination with the HomeGuard MS8000 the range is up to 10 meters. Range may vary due to battery and temperature conditions. SD10 The SD10 smoke detector does not sense gas, heat or smokeless flames! The equipment may not be modified under any circumstances. 3 SAFETY- AND MAINTENANCE- REFERENCES • Never open the equipment. No serviceable parts are inside. In the event of an error please contact your dealer. • Only operate the equipment indoors and avoid the contact with dust, strong drafts of air and direct sunlight. • Clean the equipment with a dry linen cloth, this cloth can be easily dampened. • Never use any kind of cleaning products. • The system must not be kept/operated within the reach of children. It is not a toy! • Batteries are to be handled as disposable chemicals. 4 INSTALLATION PLACES It is advisable to install several smoke detectors in your home. At least one smoke detector should be installed on each floor. This ensures that an effective warning is possible when a fire starts. One smoke detector must be installed in the area outside the bedroom which is used as the exit (corridor and/or staircase). Also ensure that you install the smoke detector at a location where it can be easily heard, even through the closed door of the bedroom! (Otherwise you will not wake up during a fire alarm!) Recommended best and acceptable locations to mount smoke detectors (figure A): The smoke detector should be installed on the ceiling in the centre of the room. Smoke rises and gathers in this area (figure B) and placing the smoke alarm here guarantees the earliest possible alarm warning. For sloping roofs, the smoke alarm should be installed about 1 meter from the highest point, as displayed in figure C. Smoke detectors can be installed in all rooms, but not in the bathroom or directly above the cooking area in the kitchen. MARMITEK Ensure that the smoke detector is not installed directly on or near large metal objects as they can affect the radio range. Before installing the SD10 smoke detector on your ceiling or the wall, ensure that the SD10 is within range of your Marmitek security system. You can test this by pushing the test button of the SD10. The Marmitek security system should now be triggered and will dial the pre- programmed telephone numbers. In the case of range problems, choose a different location for your SD10 smoke detector. Moving the SD10 just a few centimetres can make a big difference in range. To avoid false alarms, do not install the SD10 smoke detector in your kitchen, garage, in dusty places, in places with a higher than average air flow (near ventilation, open windows), near metal and in places where the temperature is below 10°C or above 37°C. 5 INSTALLATION Please follow these steps to install the Marmitek smoke detector: • Do not insert the battery at this stage (9V). Please follow the steps of the next chapter before you insert the battery. The smoke detector will not operate until you insert the battery properly. • Remove the mounting bracket from your unit by rotating it counter-clockwise. • In each of the keyhole slots, draw a mark to locate a mounting plug and screw. • Remove the bracket. • Drill two holes at the marks and insert plastic wall plugs. Ensure that the detector does not get any plaster dust on it when you drill the holes for mounting. • Attach the bracket to the wall using the two screws and plastic wall plugs (supplied) • Line up the slot of the bracket and the detector. Push the detector onto the mounting bracket and turn it clockwise to fix it into place. Pull outward on the detector to make sure it is securely attached to the mounting bracket. 6. REGISTERING THE SMOKE DETE...