Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
4. For selection of the next word (DOOR), repeat step 3, but press key [3] until the desired first letter of the next word appears (in this example, "D"). Then press key [6] to display the first available word beginning with "D". Press key [3] repeatedly until the desired word (DOOR) appears. To accept the word, press the [6] key, which again toggles back to alphabet list. .59 – Entering Zone 5. When all desired words have been entered, press key [8] to store the Descriptors description in memory. (continued) 6. To review the zone descriptions, key [#] plus zone number (e.g., #01). To edit zone descriptions, key [*] plus zone number (e.g., *01) 7. To exit the zone description mode, key 00. NOTE: Alpha descriptor entry can be entered locally at the alpha keypad or remotely using AdemcoOs V-Link. downloading software (Rev. 4 or higher) or AdemcoOs Compass Windows downloading software.. Adding Custom Words Up to 20 installer-defined words can be added to the built-in vocabulary. Each of the 20 "words" can actually consist of several words, but bear in mind that a maximum of 10 characters can be used for each word string. NOTE: The phone module can be programmed to annunciate substitute custom words, if desired. If not programmed for substitutes, the phone module will only annunciate the zone number whenever the alpha keypad displays a custom word 1. Select CUSTOM WORD mode. The keys perform the following functions: [3] Advances through alphabet in ascending order. [1] Advances through alphabet in descending order. [6] Selects desired letter; moves the cursor 1 space right. [4] Moves the cursor one space to the left. [7] Inserts a space at the cursor location, erasing any character at that location. [8] Saves the new word in the system’s memory. [*] Returns to description entry mode. 2. Key the number of the custom word or word string to be created (01-20). For example, if you are creating the first word (or word string), enter 01; when creating the second word, enter 02, and so on. A cursor will now appear at the beginning of the second line. 3. One of two methods of entering the custom word’s characters can now be used (refer to the CHARACTER LIST of letters, numbers, and symbols on the next page): a) Press the [#] key, followed by the two digit entry for the first letter you would like to display (e.g., [6][5] for "A"), or... b) Use the [3] key to advance through the list of symbols, numbers, and letters. Use the [1] key to move back through the list. When zone descriptors are being entered as described in step 3a the custom word numbers are 250 to 269 for words 1 to 20 respectively. When being entered as described in step 3b, each word will be found at the end of the group of words that begin with the same letter as it does. 4. When you have reached the desired character, press the [6] key to select it. The cursor will then move to the right, in position for the next character. 5. Repeat steps 3 and 4 to create the desired word (or words). Note that the [4] key can be used to move the cursor to the left if necessary, and that key [7] can be used to enter a blank (or to erase an existing character). Each word or word string cannot exceed 10 characters. 6. Press the [8] key to save the custom word(s) and return to the CUSTOM WORD? display. The custom word (or string of words) will be automatically added to the built-in vocabulary at the end of the group of words beginning with the same letter. 7. Repeat steps 2 through 6 to create up to 19 additional custom words (or word strings). 8. Key 00 at custom word prompt to exit the zone description programming mode. . 60 – Creating Partition 1. Select "Part DESCRIPT." mode. The system will ask for the partition number Descriptors desired. Enter the number as a single key. 2. Follow the same procedure as for CUSTOM WORDS, except that partition descriptors are limited to four (4) characters (ex. WHSE for warehouse). Creating A Custom Message Display (Installer’s Message) Normally, when the system is in the disarmed state, the following display is present on the Keypad. **** DISARMED **** READY TO ARM Part or all of the above message can be modified to create a custom installer message for each partition. For example, **** DISARMED **** on the first line or READY TO ARM on the second line could be replaced by the installation company name or phone number for service. Note that there are only 16 character spaces on each of the two lines. To create a custom display message, proceed as follows: 1. Select DEFAULT SCREEN mode. The keypad will ask for the partition number for this message. Enter the partition number. Press [*] to accept entry. The following will appear: **** DISARMED **** READY TO ARM A cursor will be present at the extreme left of the first line (over the first "star"). The [6] key is used to move the cursor to the right and the [4] key to move the cursor to the left. Key [7] may be used to insert spaces or erase existing characters. 2. For example, to repl...
Otros modelos de este manual:Detector de incendios - Ademco N7001V2 (1.4 mb)