Votos - , Puntuación media: ( )

Manual de usuario Bacharach, modelo KN-COPP-B

Fabricar: Bacharach
Tamaño del archivo: 245.61 kb
Nombre del archivo:

Idioma del manual:

El documento se está cargando, por favor, espere

Descargar ahoraCerca

El documento se está cargando, por favor, espere

Descargar ahoraCerca

The unit will not detect CO in this condition. Please replace immediately. Note: Your Kidde CO Alarm will NOT monitor CO levels while an error warning is being displayed. Low Battery If the batteries become “low”, the alarm will alert you with a short “chirp” and the red LED Figure 7 will flash once every 30 seconds for up to 7 days. The digital models will display “Lb” as shown in Fig. 7. Features and Operation of Digital Display and Non-digital Display Models (cont.) Test/Reset Button The test/reset button is used to test the unit’s electronics and to reset the unit during alarm. Test the unit: To test, press the test/reset button. Test the unit weekly! The unit will perform a self diagnostic test by cycling through the alarm pattern. Familiarize yourself and family members with the alarm pattern. A CO alarm is 4 short beeps – followed by 5 seconds of silence – followed by 4 short beeps. This cycle will repeat in the event of a CO alarm. This cycle will continue for the first 4 minutes of a CO alarm and then change to one cycle every one minute until the device is reset or the CO is eliminated. Note: For Digital Display Models After the test/reset button is pressed, numbers appear on the display. These are not CO readings and are part of the internal testing process. Ignore these numbers ! Due to the loudness of the alarm we suggest you place your fingers over the sounder opening when testing your Kidde CO Alarm. Reset If the alarm is sounding, pressing the test/reset button will terminate the alarm. If the CO condition that caused the alert in the first place continues, the alarm will reactivate. If the CO alarm sounds again within six minutes, it is sensing high levels of CO which can quickly become a dangerous situation. If this happens follow What To Do If The Alarm Soundson pages 18-20. Reactivation times depend on the amount of CO that caused the CO alarm to initially alarm and the amount of CO present after resetting the alarm. Features and Operation of Digital Display and Non-Digital Display Models (cont.) Lights MOVE TO Red Alarm Light FRESH AIR • The red light flashing once every Alarm 30 seconds, accompanied by the alarm “chirp”, indicates the Figure 8 batteries need to be replaced, or the unit has malfunctioned (see figure 8). • 4 quick flashes with alarm – followed by 5 seconds off – followed by 4 quick flashes with alarm (repeating pattern) indicates the presence of carbon monoxide. Refer to pages 1820 for instructions on What to do if the Alarm Sounds. Green Operate Light The green light indicates the unit is TEST functioning properly (see figure 9). RESET The green light will flash every 30 sec- Operate onds indicating a CO reading is being taken and when any button Figure 9 is pressed. Battery Installation/Replacement Installation/Replacement Since batteries are not installed in the unit at the factory, you will need to install them. Three AA batteries have been included with your purchase. When replacing the batteries, we recommend use of the following for a minimum of one year normal operation: • Duracell MN1500 • Energizer E91 • Rayovac 815 These batteries can be purchased at your local retailer. Note: Constant exposure to high or low humidity may reduce battery efficiency. Battery Installation/Replacement (cont.) Battery Replacement/Installation Instructions To install or replace the batteries in your Kidde unit please perform the following steps: 1. Gently flip open the lower half of the front cover to expose the battery compartment. 2. Remove the old batteries and properly dispose of them as recommended by the CARBON MONOXIDE ALARM TESTRESET Operate Alarm MOVE TOFRESH AIR Figure 10 battery manufacturer (see figure 10). 3. Reinstall the new batteries, being careful to seat the red battery warning flags in the recess of the battery well. Also, note the polarity illustration in the bottom of the battery compartment. If applicable, the unit will chirp and display for approximately one minute and return to normal operation. 4. Gently close the bottom cover. The bottom cover of your CO alarm will NOT close if all three AA batteries are not properly installed. Part Four – What to do When the Alarm Sounds ^! WARNING: Actuation of your CO Alarm indicates the presence of Carbon Monoxide (CO) which can KILL YOU. 1) Operate test/reset button; 2) Call your emergency services (fire dept. or 911); PHONE NUMBER 3) Immediately move to fresh air - outdoors or by an open door/window. Do a head count to check that all persons are accounted for. Do not re-enter the premises nor move away from the open door/window until the emergency services responders have arrived, the premises have been aired out, and your alarm remains in its normal condition. 4) After following steps 1-3, if your alarm reactivates within a 24 hour period, repeat steps 1-3 and call a qualified appliance technician to investigate for sources of CO from fuel burning equipment and appliances, and inspect for proper operation of this equ...