Votos - 3, Puntuación media: 4.3 ( )

Fabricar: Bosch Tamaño del archivo: 100.12 kb Nombre del archivo: Idioma del manual:

Ensure your security system is idle. 2. Press the [COMMAND] bar. The Command mode indicator light comes on. 3. Press the [5] key and then the [5] key again. Your security system is now in the Passcode Change Mode. 4. Enter the passcode you wish to change and press the [ENT] key. 5. Enter the new passcode and press the [ENT] key. 6. Enter the new passcode again and press the [ENT] key. 7. Test the new passcode by using it to arm and disarm the system. Do not use any of the keypad arming commands to arm the system until you are certain that the new passcode is working. Fire Test . I have this feature. . I do not have this feature. . This feature requires a passcode. Use this function to test points and other 24-hour points to be certain they function properly. You can review untested points at your keypad to help pinpoint any problems. When initiated, the Fire Test tests the fire bell pattern on the bell output and rings the keypad fire bell for 2 seconds. The AC is disabled for 4 minutes to test the system’s battery power. If the battery cannot maintain the system for the 4-minute period, the keypad appears to go dead. If this happens, contact your security company. At the end of the 4-minute period, AC returns to the system and the control panel restores. A message is be sent to your security company upon initiation and completion of the Fire Test. During the Fire Test, no 24-hour alarms are sent to your security company. If there is no activity on the system for 20 minutes, the system automatically exits from the Fire Test. COMMAND 5 8 To use Fire Test: 1. Ensure your security system is idle. 2. Press the [COMMAND] bar. The Command mode indicator light comes on. 3. Press the [5] key, and then the [8] key. Audible devices (both interior and exterior) sound the fire bell. 4. One by one, activate the detection devices to fault each point. The audible fire devices sound momentarily and the keypad display indicates the faulted point, verifying that the detection device is working properly. 5. To end the Fire Test, press any numeric key on the keypad. If no activity occurs on the system for 20 minutes, the fire test ends automatically. Watch Mode . I have this feature. . I do not have this feature. . This feature requires a passcode. With your system disarmed, use Watch Mode to monitor selected points. Each time a watch point is faulted (door or window is opened) the keypad chimes once. Note: Contact your security company to find out which points are watch points and whether or not your system automatically turns the Watch Mode on whenever you disarm. Application This command is useful in a residential system when you want to monitor entrances or exits in your home. In commercial installations, Watch Mode is used as a door chime to alert you when a customer or delivery person has entered your business. COMMAND 6 To use COMMAND 6: 1. Ensure your security system is idle. 2. Press the [COMMAND] bar. The Command mode indicator light comes on. 3. Press the [6] key. The system is now in Perimeter Watch Mode. 4. To exit the Perimeter Watch Mode, press the [COMMAND] bar and then the [6] key. Special Alert . I have this feature. . I do not have this feature. . This feature requires a passcode. This command is a manually operated and initiated alarm command. Command 7 is programmed to respond to numerous situations that can need immediate attention. This command can also send a silent alarm to your security company without sounding an alarm signal on the premises. Check with your security company for the options they offer. COMMAND 7 To engage COMMAND 7: 1. Press the [COMMAND] bar. The Command mode indicator light comes on. 2. Press the [7] key. Your COMMAND 7 special alert is programmed to: _____ notify your alarm company. _____ ring a bell on your premises. Description: Partially Turn On the Perimeter . I have this feature. . I do not have this feature. . This feature requires a passcode. This function is used to turn on the perimeter of your building while selected portions of the perimeter remain turned off. Perimeter points that are not secure (faulted) when this function is entered are not included in the system. This function does not turn on the interior of your building. Entry/exit delays are provided with this arming command. Application Use this function in residential systems to turn on the front of your house while the interior and the rear perimeter doors are turned off, giving you freedom of movement between the house and patio. In commercial systems, when you need access to the large overhead doors to receive deliveries, this function allows you to keep the rest of the building perimeter armed. COMMAND 8 To arm with COMMAND 8: 1. Ensure the keypad is disarmed. 2. Decide which points are to be left disarmed. Fault the points (doors and windows) by leaving them open. The point(s) must remain open until after the exit delay time expires. 3. Press the [COMMAND] bar. The Command mode indicator light comes on. 4...

Descargar ahora

Introduzca dos números de la imagen: