Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
The DF-72/EC sounds a local alarm as soon as smoke is detected. Twenty seconds after the local alarm sounds, the DF-72/EC’s transmitter will send an alarm signal to the console. The alarm signal will be repeated every 20 seconds as long as smoke is still present. Coding switches are not required or used in the DF-72/EC. Each transmitter is pre-coded at the factory to a unique code. With the DX format, there are more than one million codes possible. The smoke detector and transmitter are powered by two 9-volt batteries. These batteries are supplied with the transmitter and can power the unit for up to two years. If the battery voltage drops below a preset level, a low battery report is sent to the receiver every hour. NOTE: After replacing batteries, press transmitter test button to reset “low battery circuit” STEP 1 Remove mounting plate. Remove the unit’s mounting plate by turning the plate counterclockwise. STEP 2 Identify components. Examine the DF-72/EC to identify the component locations. STEP 3 Install batteries. Connect the two 9-volt batteries and place them into the battery compartments. STEP 4 Pick smoke detector location. Referring to the NFPA standard on the back of this sheet, select a good location to mount the DF-72/EC. Mounting the DF-72/EC on foilbacked wallpaper or on a metal single-gang electrical box is not recommended because the radio range will be reduced. STEP 5 Install mounting plate. Use the two screws and anchors provided to attach the mounting plate to the wall or ceiling. Alternately, the mounting plate can be attached to a plastic single-gang electrical outlet box. For the best radio range, observe the “best signal” label on the bottom of the unit. STEP 6 Program into receiver. Follow the DF-16/EC console’s instructions to set it in a program or learn mode. Press the transmitter test button (not the smoke detector’s test button) to send a test signal. The transmit LED should light. Verify that the signal was received and that the transmitter was properly entered into the console’s memory. (760) 438-7000 • FAX (760) 438-7043 BY TWIST MOUNTING PLATE TO UNLOCK REMOVE MOUNTING PLATE BATTERY COMPARTMENTS TRANSMITTER BOARD TRANSMIT LED TRANSMITTER TEST BUTTON CONNECT AND INSTALL TWO 9-VOLT ALKALINE BATTERIES DINING KITCHEN BEDROOM BEDROOM LIVING BEDROOM ROOM SMOKE DETECTOR PLASTIC SINGLE-GANG ELECTRICAL BOX SCREW ANCHORS FOR WALLBOARD OR ENTER YOUR SECRET CODE PRESS LEARN ENTER AN UNUSED SENSOR NUMBER SEND SIGNAL FROM SMOKE DETECTOR START IN OFF MODE HOLD OFF BUTTON FOR 3 SECONDS WHEN FINISHED TO EXIT LEARN MODE PRESS AND RELEASE TRANSMITTER TEST BUTTON TO SEND A TEST SIGNAL RED TEST LIGHT LEARN BUTTON STEP 7 Attach DF-72/EC to mounting plate. Match up alignment tabs on detector and plate. Turn detector clockwise until it locks in place. STEP 8 Test smoke detector. Set the console into a test mode. Press and hold the smoke detector test button. Continue to hold the test button for at least 30 seconds after the noisemaker starts. Verify that the signal was received. NFPA 74 STANDARD FOR SMOKE DETECTOR LOCATION The DF-72/EC should be installed in accordance with National Fire Protection Association (NFPA) Standard 74, which reads as follows: 2-1.1.1Smoke detectors shall be installed outside of each separate sleeping area in the immediate vicinity of the bedrooms and on each additional story of the family living unit including basements and excluding crawl spaces and unfi nished attics*. The provisions of 2-1.1.1 represent the minimum number of detectors required by this standard. It is recommended that the householder consider the use of additional smoke or heat detectors for increased protection for those areas separated by a door from areas protected by the required smoke detectors under 2-1.1.1 above. The recommended additional areas are: living room, dining room, bedroom(s), kitchen, attic (fi nished or unfi nished), furnace room, utility room, basement, integral or attached garage and hallways not covered under 2- 1.1.1 above. However, the use of additional detectors remains the option of the householder. 2-1.1.2 For family living units with one or more split levels (i.e., adjacent levels with less than one full story separation between levels), a smoke detector required by 2-1.1.1 shall suffi ce for an adjacent lower level, including basements. MATCH UP ALIGNMENT TABS TWIST DETECTOR CLOCKWISE TO LOCK TO MOUNTING PLATE EMERGENCY PLACE CONSOLE IN OFF MODE TO STOP SIREN, CHECK THAT THE SENSOR STATUS LIGHT IS BLINKING PRESS AND HOLD DETECTOR TEST BUTTON, SMOKE DETECTOR'S BEEPER WILL START TO SOUND CONTINUE TO HOLD THE SMOKE DETECTOR'S TEST BUTTON FOR ABOUT 30 SECONDS UNTIL THE CONSOLE'S SIREN STARTS NFPA 74 STANDARD FOR SMOKE DETECTOR LOCATION Exception: Where there is an intervening door between one level and the adjacent lower level, a smoke detector shall be installed on the lower level. Ceiling mounted smoke alarms should be located in the center of the room o...