Votos - 4, Puntuación media: 4.3
(
)
)
|
Resumen del manual
PIR 720 120VAC, 60 Hz, 100W Max. M06-9007-001 5/01 IMPORTANT! PLEASE READ CAREFULLY AND SAVE. This user’s manual contains important information about your Motion Sensing Hands Free Socket’s operation. If you are installing this unit for use by others, you must leave this manual—or a copy of it—with the end user. mounted lower than 8 feet, it will not “see” quite as far. Do not mount the Motion Sensing Hands Free Socket higher than 10 feet from the floor. LIMITATIONS OF MOTION SENSING HANDS FREE SOCKET This Motion Sensing Hands Free Socket: • Is for indoor use only. • Requires AC power to function properly. If AC power to the unit is cut off, it will not work. • Is NOT intended to serve as a safety or security device. It is designed for convenience only. This Motion Sensing Hands Free Socket will not work properly if: • The socket to which it is connected is defective or if the bulb is burned out. • It is used with anything other than a ceiling-mounted, bare bulb light socket. Although the Motion Sensing Hands Free Socket detects changes in temperature, it is not intended to be used as a heat and/or fire detector. Consult NFPA Standard 72, National Fire Alarm Code, for residential smoke detection and fire protection guidelines. Although this Motion Sensing Hands Free Socket detects motion 360., the unit responds more effectively at each 180. point. (See figure right.) The 180. points are marked on the top of the unit by arrows. After installing the unit, rotate it until either arrow faces the general direction of the path people will most likely cross. This device is designed for INDOOR USE ONLY. Do not allow it to get wet. Infrared cannot penetrate glass or plastic. Do not use in a glass-enclosed light or shaded lamp. USE ONLY WITH A CEILING-MOUNTED, BARE BULB LIGHT SOCKET. INSTALLING THE MOTION SENSOR Never touch the Motion Sensing Hands Free Socket, bulb, or socket with wet hands or when the floor is damp or wet. Turn the light OFF when installing the unit. 1. Turn the power to the light socket you have chosen OFF. 2. Remove the light bulb from the socket. 3. Screw the Motion Sensing Hands Free Socket directly into the empty socket. 4. Screw the light bulb into the Motion Sensing Hands Free Socket. 5. Turn the power ON. After several seconds, the light will turn on. The light will remain on for approximately 4 minutes after you leave the area. (A built-in delay of several seconds allows the light bulb to cool before the motion sensor is able to detect motion again.) The unit is now ready to operate automatically. It is possible that the light may turn off while you are within the sensing area. For example, you may have been standing still. TROUBLESHOOTING CONSUMER AFFAIRS 1-800-323-9005 The lights do not turn on 1. Bulb is burned out when movement is detected 2. Power switch is OFF 3. Bulb is less than 25 watts 4. Rotate directional alignment arrows The lights turn on and off 1. Bulb is more than 100 watts repeatedly 2. Motion Sensing Hands Free Socket must be mounted at least 12 inches from any wall or door 3. Heat sources in target area The light stays on 1. Bulb is more than 100 watts continuously 2. Motion Sensing Hands Free Socket must be mounted at least 12 inches from any wall or door 3. Heat sources in target area 4.Temporary power failure–turn light off and on again Sensing range is reduced 1. Very warm temperatures can temporarily reduce the sensing range of the Motion Sensing Hands Free Socket NOTE: If the Motion Sensing Hands Free Socket is less than 12 inches away from a door or wall, reduce bulb wattage or apply masking or electrical tape over a portion of the sensor lens in direct line with the wall or door to reduce reflection. CLEANING AND REPAIRING To clean the Motion Sensing Hands Free Socket: 1. Turn the light OFF. 2. Remove the Motion Sensing Hands Free Socket and bulb from the light socket. 3. Wipe the unit with a soft cloth. Do not use harsh cleaners of any kind. Do not allow the unit to get wet or be submerged in water. Never touch the Motion Sensing Hands Free Socket, bulb, or socket with wet hands or when the floor is damp or wet. Always turn the light OFF when cleaning. Do not attempt to repair your Motion Sensing Hands Free Socket yourself. If it does not appear to be working properly and it is still under warranty, return it to BRK Brands, Inc. If the unit is no longer under warranty, please discard it and replace it with a new unit. LIMITED WARRANTY Coverage: BRK Brands, Inc. warrants its enclosed Motion Sensing Hands Free Socket to be free from defects in materials and workmanship under normal use for a period of three years from the date of purchase. During the first year after the date of purchase, BRK Brands, Inc. will replace any defective Motion Sensing Hands Free Socket without charge. During the next two years, BRK Brands, Inc. will replace any defective Motion Sensing Hands Free Socket at a charge to you not to exceed BRK Brands, Inc.’s cost. This is your exclusive w...