Votos - 5, Puntuación media: 3.6
(
)
)
|
Resumen del manual
The diagram shows the first and last gobo on each wheel, as per the DMX Values tables. Rotating Gobos Fixed Gobos Extra Gobos Color Wheel Legend 300E Spot User Manual Rev. 01g -7- Setup Gobo Replacement Procedure Gobo Replacement Diagram _chiTyet. The gobos in the Legend 300E Spot’s gobo wheel are removable from their gobo plates. This operation is quite simple, although it requires the technician to be careful and to follow the recommended procedure. • Make sure to disconnect the fixture’s power cord before replacing a gobo • Always replace a gobo with a gobo of the same dimensions. • When inserting a glass gobo, always make sure that the shinny side of the gobo (glass base) faces the lamp. This provides a layer of protection against the high temperature from the lamp. 1) Turn the fixture off and disconnect it from the power outlet. 2) Open the head cover by loosening the four fastening screws at the sides of the top cover. 3) Separate the gobo plate away from the gobo wheel by pushing it toward the front of the moving head (direction 1 in the diagram). Be careful not to push the gobo out of the gobo plate. 4) Extract the gobo plate by pulling it outward (direction 2 in the diagram). 5) On a flat surface, remove the expansion ring that holds the gobo in place and remove the gobo from the gobo plate. 6) Insert a new gobo and hold it in place with the expansion ring. 7) Slide the tip of the gobo plate under the pressure plate near the center of the gobo wheel. 8) Push the gobo plate inwards. DO NOT force the gobo plate into the gobo wheel slot. If correctly installed, the gobo plate should accommodate itself in the gobo wheel slot. -8- Legend 300E Spot User Manual Rev. 01g CHRÏÏVEl Setup Lamp Replacement Procedure The Legend 300E Spot is equipped with a Philips MSR Gold 300/2 lamp. This lamp uses a socket called FastFit, which allows for fast and easy lamp changes. Follow the procedure below to safely change the Legend 300E Spot’s lamp. 1) Turn the fixture off and disconnect it from the power outlet. 2) Wait at least 15 minutes for the lamp to cool down. 3) Loosen the two screws on the lamp cover (marked “A” in the diagram). 4) Lift and rotate the lamp cover as per the diagram to expose the base of the lamp. 5) Rotate the ceramic base of the lamp 90° counterclockwise. 6) Pull the lamp out by holding it from its base only. 7) Insert the new lamp and turn it 90° clockwise. 8) Reverse steps 3 and 4. 9) Use the adjustment screws (marked “B” in the diagram) to position the lamp in the center of the reflector to obtain the best output. Lamp Replacement Diagram Increasing the • ALWAYS turn the lamp off by using the DMX controller or the fixture’s control panel. Lamp’s Life Then wait at least five minutes before switching off the fixture. This will keep the fans running to extract any remaining heat from the fixture’s head. DO NOT power cycle the fixture unless it is necessary. DO NOT touch the lamp without wearing gloves to avoid leaving grease on the bulb or on the contacts that could reduce the lamp’s life. ALWAYS change the lamp when it has reached its recommended lifespan to avoid the risk of lamp explosion. Legend 300E Spot User Manual Rev. 01g -9- Setup Mounting Orientation Rigging Procedure Product Mounting Diagram Before mounting this fixture, read and follow the safety recommendations indicated in the Safety Notes (page 2 of this manual). Always mount this fixture in any safe position while making sure that there is adequate room around it for ventilation. Make sure to mount this fixture away from any flammable material as indicated in the Safety Notes (page 2 of this manual). CHAUVET® recommends following the general guidelines below when mounting the Legend 300E Spot. • When selecting an installation location, consider ease of access to the fixture for operation, programming adjustments, and routine maintenance. • Never mount the fixture in places where rain, high humidity, extreme temperature changes, or restricted ventilation may affect it. • If hanging this fixture, make sure that the location where you are mounting the fixture can support its weight. Please see the Technical Specifications section of this manual for the weight requirement of this fixture. The Legend 300E Spot comes with an already installed mounting bracket to which you will be able to attach the two included omega clamps. Be aware that you will have to use two mounting points per fixture. In addition, you will have to use a safety cable (not included) to link the fixture to the structure. -10- Legend 300E Spot User Manual Rev. 01 g CHRÛVET Operation 4. Operation Control Panel Description LCD Display Control Options Programming Navigation Buttons Button Function