Cut along the dotted lines and place the corrugated protector over the top and front of the tub. The center cut-out drops into the center of the tub. After measuring the dimensions of the product, frame the construction area. Locate the tub in position and mark a joist so that a 2x4 stringer can be nailed in place. The stringer will be located under the flange against the wall. Nail in place the 2x4 support. Re-position the tub and check for level, both front to back and left to right. It ma

1.1 Recommended Tools Tape Measure Regular Screwdriver Phillips Screwdriver CARE INSTRUCTIONS: DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH. DO NOT: CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A COARSE SURFACE. TOWEL RING, ROBE HOOK and TISSUE HOLDER MOUNTING BRACKET INSTALLATION The TOWEL RING, ROBE HOOK and TISSUE HOLDER work best if secured to a wall stud or cross brace within the wall, using 1-1/

1.1 Recommended Tools Tape Measure Regular Screwdriver Phillips Screwdriver CARE INSTRUCTIONS: DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH. DO NOT: CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A COARSE SURFACE. TOWEL RING, ROBE HOOK and TISSUE HOLDER MOUNTING BRACKET INSTALLATION The TOWEL RING, ROBE HOOK and TISSUE HOLDER work best if secured to a wall stud or cross brace within the wall, using 1-1/

If MOUNTING BRACKET (1) is secured to a stud or cross brace drill small pilot holes for SCREWS (3). (NOTE PROPER POSITION OF MOUNTING BRACKET FOR ACCESSORY TO BE INSTALLED.} For installations on drywall or tiled walls, use ANCHORS (4) and SCREWS (2) for securing MOUNTING BRACKETS (1) to wall. Use MOUNTING BRACKET (1) as a template and mark the mounting holes. Drill three 1/8" diameter holes a minimum of 1-1/4" deep. Insert the three ANCHORS (4) flush with face of the finished wall. Secure MOUN

Secure accesory with SET SCREW (3) using 2.5mm HEX WRENCH (4) supplied. (NOTE POSITION OF MOUNTING BRACKET.} 2 POSITION OF MOUNTING BRACKET FOR TOWEL RING AND ROBE HOOK 2 ROBE HOOK AND TISSUE HOLDER INSTALLATION Align accessory (C, D) and place ESCUTCHEON (1) onto MOUNTING BRACKET (2). Secure accesory with SET SCREW (3) using 2.5mm HEX WRENCH (4) supplied. (NOTE POSITION OF MOUNTING BRACKET.} 3 2 HOOK AND TISSUE HOLDER M968630 Rev. 1 .1

1/2" NOM. COPPER SWEAT TUB 1/2" NOM. COPPER SWEAT 2" SWEAT INLETS SWEAT INLETS (STOPS) SHR. 1/2" NOM. COPPER SWEAT TUB 1/2" NOM. COPPER SWEAT 4-1/16" 5-7/8" INLETS 1/2" NOM. COPPER SWEAT FINISHED WALL 4" BOTTOM OF TUB 74" FOR HEAD CLEARANCE 5-1/8" REF. 7-7/8" REF. 18" OPTIONAL 5" REF. 1/2" NPT 1-5/8" to 3-1/4" 1/2" NPT 7-1/8" OPTIONAL TO FINISHED FLOOR USUALLY BETWEEN 65'' AND 80'' TOP OF TUB RIM 1-1/2" REF. Channel Locks Flat Blade Screwdriver Plumbers' Putty or Caulking Phillips Screwdriver M9

DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH. DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A COARSE SURFACE. CARE INSTRUCTIONS: 1 INSTALL DIVERTER When finished tiling the wall, remove PLASTER GUARD (1). Remove two screws that secure the DIVERTER LID (2) and remove Lid. Inspect the inside surface of diverter port. Diverter port must be free of any dirt. Clean if necessary. Install DIVERTER (3) w

(66 Kg.) 895 Lbs. (406 Kg.) 90 Gal. (341 L) 40 Gal. (151 L) 55-1/2 x 28-3/4 In. (1410 x 730mm) 62 x 49-3/4 In. (1575 x 1264mm) 13-3/8 In. (340mm) 25 Lbs./Sq.Ft. (123 Kgs./Sq.m) 27.552ELECTRICAL SPECIFICATIONSINSTALLED SIZEWEIGHTWEIGHT w/WATERGAL. TO OVERFLOWMIN. OPERATING GAL. BATHING WELL AT SUMPBATHING WELL AT RIMWATER DEPTH TO OVERFLOWFLOOR LOADING(PROJECTED AREA) PTS. CUBE (FT3) 1.4 HPR, 9.7 AMPS, 120V.PUMPGENERAL SPECIFICATIONS FOR 237172 x 36 x 21-3/4 In.(1829 x 914 x 552mm) 100 Lbs. (45 K

• Clean the surrounding surface immediately after using caustic drain cleaners. • Burning cigarettes will damage the surface. • Should damage to the fixture occur, repairs can be made quickly and easily. Your distributor or builder can provide details. • Do not permit drain cleaner to enter the circulation system. CIRCULATION SYSTEM CLEANING-PURGING PROCEDURESSTEP 1. Once every month purge and clean the circulating system. Fill whirlpool with warm water and add two teaspoons of dishwasher deterg

for selecting an American Standard bath. Your new bath is shipped to you after careful inspection. The whirlpool version is completely assembled with pump, motor, and system piping. All you need to finish the whirlpool installation are your selected fittings and electrical connections. To insure maximum performance and pleasure from this product, please follow the instructions and cautions. CORNER DUET W/SEAT 60" x 60" MODEL 2351CENTURION 6' x 36" MODEL 2371CONTEMPO OVAL MODEL 2383FREE SPIRIT 6'