Gals 291.5 (min) 375 (max) L Electrical Specifications Each component requires a separate, dedicated GCFI protected circuit Motor/Pump 120V 20A 60HZ Heater 120V 15A 60HZ FEATURES, UPGRADES & ACCESSORIES Material Type: High-Gloss Acrylic Install Type: Drop-in with wood frame or Undermount Available Colors: White (W), Almond (A), Oyster (Y), Black (B) Cut-out: 69” x 33” or Undermount Template DD42000 Standard (Included) Features: 14 jets, In-line Heater, Chromatherapy lighting, infinity e

Cut along the dotted lines and place the corrugated protector over the top and front of the tub. The center cut-out drops into the center of the tub. After measuring the dimensions of the product, frame the construction area. Locate the tub in position and mark a joist so that a 2x4 stringer can be nailed in place. The stringer will be located under the flange against the wall. Nail in place the 2x4 support. Re-position the tub and check for level, both front to back and left to right. It ma

Always check to make sure that the Elevated Toilet Seat is properly and securely locked in place before using. Ensure that all four (4) mounting brackets are adjusted to the same height-otherwise injury or damage may occur. Be sure to center your weight on the Elevated Toilet Seat because the seat may tip if you lean too far forward or to either side. Users with limited physical capabilities should be supervised or assisted when using the Elevated Toilet Seat. The Elevated Toilet Seat has a reco

Pongase en cantacto con el agente de la entrega o su proveedor, para futuras instrucciones. SUMARIO DE PRECAUCIONES Las recomendaciones siguientes se hacen para asegurar la apropiada y segura instalacion del Asiento Elevado para Retrete: ADVERTENCIA NO Instale este equipo sin antes leer y entender esta hoja de instrucciones. Si tiene dificultad en entender estas advertencias, precauciones e instrucciones, pongase en contacto con un profesional de la salud, su proveedor o personal tecnico, si apl

2. Levante el frente del asiento hasta que el soporte ajustador quede libre, fuera del labio del retrete. 3. Jale el asiento, levantandolo hacia usted en un angulo, removiendolo del retrete. 4 GARANTIA NOTA: ESTA GARANTIA HA SIDO ESCRITA PARA CUMPLIR CON LA LEY FEDERAL DE LOS ESTADOS UNIDOS APLICABLE A PRODUCTOS DESPUES DEL 4 DE JULIO DE 1975. Esta garantia se extiende unicamente al comprador/usuario original de nuestros productos. Esta garantia le da derechos legales especificos y usted pudiera

1.1 Recommended Tools Tape Measure Regular Screwdriver Phillips Screwdriver CARE INSTRUCTIONS: DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH. DO NOT: CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A COARSE SURFACE. TOWEL RING, ROBE HOOK and TISSUE HOLDER MOUNTING BRACKET INSTALLATION The TOWEL RING, ROBE HOOK and TISSUE HOLDER work best if secured to a wall stud or cross brace within the wall, using 1-1/

1.1 Recommended Tools Tape Measure Regular Screwdriver Phillips Screwdriver CARE INSTRUCTIONS: DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH. DO NOT: CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A COARSE SURFACE. TOWEL RING, ROBE HOOK and TISSUE HOLDER MOUNTING BRACKET INSTALLATION The TOWEL RING, ROBE HOOK and TISSUE HOLDER work best if secured to a wall stud or cross brace within the wall, using 1-1/

If MOUNTING BRACKET (1) is secured to a stud or cross brace drill small pilot holes for SCREWS (3). (NOTE PROPER POSITION OF MOUNTING BRACKET FOR ACCESSORY TO BE INSTALLED.} For installations on drywall or tiled walls, use ANCHORS (4) and SCREWS (2) for securing MOUNTING BRACKETS (1) to wall. Use MOUNTING BRACKET (1) as a template and mark the mounting holes. Drill three 1/8" diameter holes a minimum of 1-1/4" deep. Insert the three ANCHORS (4) flush with face of the finished wall. Secure MOUN

Secure accesory with SET SCREW (3) using 2.5mm HEX WRENCH (4) supplied. (NOTE POSITION OF MOUNTING BRACKET.} 2 POSITION OF MOUNTING BRACKET FOR TOWEL RING AND ROBE HOOK 2 ROBE HOOK AND TISSUE HOLDER INSTALLATION Align accessory (C, D) and place ESCUTCHEON (1) onto MOUNTING BRACKET (2). Secure accesory with SET SCREW (3) using 2.5mm HEX WRENCH (4) supplied. (NOTE POSITION OF MOUNTING BRACKET.} 3 2 HOOK AND TISSUE HOLDER M968630 Rev. 1 .1