Votos - 1, Puntuación media: 4
(
)
)
|
Resumen del manual
You should feel the printer seating and locking in place. 7. b. Press SELECT twice. The MenuMap prints. Models with Control Button: a. Press the Control Button to take the printer off-line. b. Press and hold down the control button for at least 2 seconds, but less than 5 seconds. The MenuMap prints. 11. Look for TRAY2 on the first page of the MenuMap under the MEDIA MENU listing. If it isn’t there, check to be sure that the connection between the printer and Tray 2 is secure, then reprint and recheck the MenuMap. 12. Check the MEDIA MENU settings shown on the MenuMap and make any needed changes for © 2004 Oki Data Americas, Inc. Note the location of the pins (1), connector (2) and tray opening (3). 8. Reattach the interface cable. 9. Plug in the power cord and turn on the printer. 10.Verify installation Models with Operator Panel: Attach the connection cable. • TRAY2 PAPERSIZE • TRAY2 MEDIATYPE • TRAY2 MEDIAWEIGHT to match the print media you will normally use in Tray 2. (If you need help with this, see “Operator Panels” in your on-line User’s Guide. Load Paper 1. Pull out the tray. 2. Position the paper guides in the tray. (continued on back) 58366302 3. Fan the paper. paper (up to 500 sheets 20-lb. US Bond). Keep the stack below the full line (2). 5. Lower the paper bar and push the tray back into the printer. Note: To install paper in Tray 1: a. Open the Tray 2 front panel. b. Slide Tray 1 out. AUTOFEED To set the printer to switch to Tray 2 when Tray 1 is empty: Printers with Operator Panel: Set AUTOTRAY on in the Print Menu. Printer with online Status Monitor: Go to the Paper tab in the Status Monitor. Select Auto Tray Switch. Activate the Tray in the Printer Driver Windows® PCL Driver 1. Click Start ^ Settings ^ Printers [Printers and Faxes for XP]. The Printers (Printers and Faxes) dialog box opens. 2. Right click the Oki printer icon, then click Properties. 3. Click the Device Option(s) tab. 4. For Available Tray, select Lower Cassette. 5. Click OK, then close the Printers (Printers and Faxes) dialog box. PostScript Emulation Driver, (Printers with Postscript option installed). 1. Click Start ^ Settings ^ Printers [Printers and Faxes for XP]. The Printers (Printers and Faxes) dialog box opens. 2. Right click the Postscript emulation printer icon, then click Properties. 3. Next: - Windows XP, 2000 and NT 4.0: click the Device Settings tab. - Windows Me and 98: click the Device Options tab. 4. Then: - Windows XP, 2000, NT 4.0 and Me: under Installable Options, click Available Tray and select 2. - Windows 98: under Change setting for Available Tray, select 2 (1 Optional Tray). 5. Click OK, then close the Printers (Printers and Faxes) dialog box. Macintosh® PostScript Emulation Driver, (Printers with PostScript option installed) OS 8.x and 9.x 1. Activate Chooser from the Apple menu. 2. Select LaserWriter 8. 3. Click Printer ^ Setup. 4. Click Configure. 5. Change the Available Tray setting to 2 (1 Optional Tray). 6. Click OK twice. 7. Close Chooser. OS X.1 No activation is required for Macintosh OS X.1. OS X.2 1. Activate Print Center from Local Hard Drive ^ Applications ^ Utilities ^ Print Center. 2. Highlight the printer name and select from the menu Printers ^ Show Info. 3. Click the Available Tray drop-down menu and select 2 (1 Optional Tray). 4. Click Apply Changes and exit to the desktop....