Votos - 4, Puntuación media: 4.3
(
)
)
|
Resumen del manual
For moredetailed information, please refer to the user’s manual on the supplied CD. Connect the Router Note: Prior to connecting the router, be sure to power off your computer, DSL/Cable modem, and the router. Step 1 Connect one end of a network cable to the WAN port of the router and connect the other end of the cable to the DSL/Cable modem. Step 2 With another network cable, connect one end of the cable to your computer’s network card and connect the other end to one of the LAN ports of the router. Step 3 Power on the DSL/Cable modem and wait for the lights on the modem to settle down. Step 4 Power on the router by connecting one end of the supplied power adapter to the power jack of the router and connecting the other end to an electrical outlet. Step 5 Power on your computer. Step 6 Make sure the WAN and the LAN port that the computer is connected to are lit. If not, try the above steps again. Section 2 Section 2 Verify Connection to Router Step 1 Go to Start, Run, type command (for Windows 95/98/ME) or cmd (for Windows 2000/XP) andclick OK. You will see the command prompt as below. Step 2 Type ping 192.168.1.1 and press Enter. You should get four reply responses back. Step 3 If you get Request timed out, or Destination host unreachable, double-check the network cable connection between the computer and the router and try Step 2 again. If you still encounterproblem, go to the next step; otherwise proceed to Section 3, Configure the Router. Step 4 For Windows 2000/XP, type ipconfig/release and press Enter. Step 5 Type ipconfig/renew and press Enter. You should get an IP address of 192.168.1.x (where x is a number between 2 - 254). Proceed to Section 3, Configure the Router. If you don’t get an IPaddress, reset the router by holding in the reset button at the back of the router for 10 seconds while it isON and try ipconfig/renew again. Step 6 For Windows 95/98/ME go to Start, Run, type winipcfg and click OK. Step 7 Select your network card from the drop-down menu and click Release. Step 8 After your IP address is released, click Renew. You should get an IP address of 192.168.1.x (where x is a number between 2 - 254). If you don’t get an IP address, reset the router by holding in thereset button at the back of the router for 10 seconds while it is ON and try Renew again. Section 3 Configure the Router Step 1 Open the web browser and type 192.168.1.1 in the URLAddress field and press Enter. Step 2 Enter admin for the password field and click Log in. Step 3 Click on Wizard from the main menu to open the Setup Wizard. Step 4 Click Next to begin the Setup Wizard. Step 5 Select your WAN Type (Internet Connection Type) and click Next. If you are not sure what your Internet Connection Type is, please contact your Internet Service Provider (ISP) for assistance. Static IP If your ISP provided you with a static IP address, select ISP assigns you a static IP address (Static IPAddress) and click Next. Proceed to Step 6, Static IP. Cable Modem If you use cable modem, select Obtain an IP address from ISP automatically (Dynamic IP Address) and click Next. Proceed to Step 6, Cable Modem. Road Runner If your ISP is running Road Runner Session Management, select Dynamic IP Address with Road Runner Session Management (e.g. Telstra BigPond) and click Next. Proceed to Step 6, Road Runner. DSL If you use DSL, select Some ISPs require the use of PPPoE to connect to their services (PPPover Ethernet) and click Next. Proceed to Step 6, DSL. PPTP If you use PPTP, select Some ISPs require the use of PPTP to connect to their services (PPTP) and click Next. Proceed to Step 6, PPTP. L2TP If you use L2TP, select Some ISPs require the use of L2TP to connect to their services (L2TP) and click Next. Proceed to Step 6, L2TP. Step 6 Follow the steps below according to your Internet Connection Type. Static IP Fill in the applicable fields according to the information provided by your ISP. Click Next when done and proceed to Step 7. Cable Modem If your ISP has provided you with a host name, enter it in the Host Name field. If your ISP requires aregistered MAC Address, click on the Clone MAC button. Click Next when done and proceed to Step 7. Road Runner Fill in the applicable fields according to the information provided by your ISP. Click Next when done and proceed to Step 7. DSL Fill in the applicable fields according to the information provided by your ISP. Click Next when done and proceed to Step 7. Note: Depending on the ISP, you may need to include the domain name with your account name. Example: username@sbcglobal.net PPTP Fill in the applicable fields according to the information provided by your ISP. Click Next when done and proceed to Step 7. L2TP Fill in the applicable fields according to the information provided by your ISP. Click Next when done and proceed to Step 7. Step 7 Click Reboot to apply your settings. Step 8 Click OK to confirm reboot. Step 9 Wait for the router to reboot and proceed to Section 4, Verify Connection Status. ...