Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
Cartridges are vacuum packed to maintain reliability. Canada only: For French speakers, remove sticker(s) from the backing sheet and place over the corresponding text on the control panel. Remove all protective materials including from inside the paper cassette. 1 Lift the scanner and remove the transportation lock. 2 Store the transportation lock as shown. 3 Close the scanner. 1 Unpack Start Here (Included for Canada only) Series Power cord 1 Connect the power cable. Caution: Do not connect to your computer yet. 2 Press the On button, then raise the control panel. To lower the control panel, press the Unlock button. Caution: To avoid damaging your Artisan 710 Series, always press the Unlock button to lower the control panel. Note: For more information on using and adjusting the control panel, see your Quick Guide. 2 Turn on and adjust 4 Install ink cartridges Note: Do not load paper yet. 1 Lift up the scanner. 3 Select language Press or to select your Language, then press OK. 5 Load paper The paper cassette has 2 trays. The main tray is for letter-size, legal-size, or 8 x 10-inch paper. The photo tray is for 4 x 6- or 5 x 7-inch photo paper. 1 Pull out the paper cassette. Then slide back the photo tray and lift it up. 2 Squeeze the edge guides and slide them out. Then insert paper with the glossy or printable side face-down. 2 Unpack the ink cartridges. 3 Remove only the yellow tape from each cartridge. Caution: Don’t remove any other seals or the cartridges may leak. 4 Insert the cartridges in the holder for each color. Press each cartridge down until it clicks. 5 Lower the scanner. 6 Wait while ink charges. Charging takes about 5 minutes. Note: Your Artisan 710 Series ships with full cartridges and part of the ink from the first cartridges is used for priming the Artisan 710 Series. Replacement cartridges will print more pages. Caution: Don’t turn off the Artisan 710 Series while the ink system is charging or you’ll waste ink. 3 Slide the edge guides against the paper. 4 Lower the photo tray. 5 Squeeze the edge guides and slide them out. Then insert 4 x 6-inch or 5 x 7-inch photo paper with the glossy or printable side face-down. Note: Make sure the paper fits under the edge guide. 6 Slide the edge guides against the paper. 7 Keep the cassette flat as you insert it. 8 Extend the output tray and flip up the stopper. Network (wireless or wired) See your Network Installation Guide. You can’t install your software as described below. OR USB connection Make sure you have a USB cable (not included). Then follow the steps below. USB connection Follow these steps to connect the Artisan 710 Series directly to your computer using a USB cable (not included). Windows® 1 Make sure the Artisan 710 Series is NOT CONNECTED to your computer. Note: If you see a Found New Hardware screen, click Cancel and disconnect the USB cable. You can’t install your software that way. 2 Insert the Artisan 710 Series software CD. With Windows Vista®, if you see the AutoPlay window, click Run Setup.exe. When you see the User Account Control screen, click Continue. 3 Click Install and follow the on-screen instructions. 4 When you see this screen, select Install driver for direct USB connection and then click Next. 6 Choose your connection 5 When prompted, connect a USB cable. Use any open USB port on your computer. Note: If installation doesn’t continue after a moment, make sure you securely connected the USB cable and turned on the Artisan 710 Series. 6 Follow the on-screen instructions to install the rest of the software and register your Artisan 710 Series. Be sure to register your Artisan 710 Series to receive these great benefits: 2-year limited warranty and 2-year toll-free customer support.* 7 When you’re done, eject the CD. You’re ready to go! Enjoy your Artisan 710 Series! See your Quick Guide or online Epson Information Center. Macintosh® 1 Make sure the Artisan 710 Series is NOT CONNECTED to your computer. 2 Insert the Artisan 710 Series software CD. 3 Double-click the Epson icon. 4 Click Install and follow the on-screen instructions. 5 When you see this screen, select Install driver for direct USB connection and then click Next. 6 When prompted, connect a USB cable. Use any open USB port on your computer. Make sure the Artisan 710 Series is securely connected and turned on. If you’re using Mac OS X 10.5.x, skip to step 9. If you’re using Mac OS X 10.3.9 or 10.4.11, continue with the next step. Any questions? Quick Guide Basic instructions for scanning, printing, copying, scanning, and using the control panel. Online Epson Information Center Click the desktop shortcut for easy access to the Artisan 710 Series user’s guide, How-to videos, FAQs, online troubleshooting advice, and software downloads. You can also purchase paper and ink. Note: You will need an Internet connection to view the Epson Information Center. If you can’t find the desktop shortcut, you can also view the Epson Information Center at epson.com/support. Network...