Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
FIGURE 40 CURVED DECORATIVE PANEL REMOVAL Insert a gloved hand behind the top right hand corner of the panel and pull forward gently. Slide your hand down along the edge of the panel allowing it to come out of its place in the fi rebox and to rest on the edge of the fi rebox opening. Repeat on the left side. Guide the panel out of the fi rebox by rotating it carefully from the left to the right, being sure to stay clear of the burner. (Fig. 40) Note: Be careful when bending the panel not to bend the panel out of shape permanently. BURNER BASE REMOVAL FIGURE 39 BOWL, MESH & ROCK REPLACEMENT SCREW W/ SPACER 1. Carefully slide the opening in the rear of the bowl over the burner making sure to line the holes in the bottom of the bowl with the 2 locating pins on the burner bottom. (Fig. 37) 2. Place the steel mesh inside the bowl making sure there is even space between the mesh and edge of bowl. (Fig. 38) FIGURE 36 18 W415-0583 / D / 07.24.07 3. Remove optional front, glass door, bowl w/ rocks, burner, decorative panel, & burner bottom. 4. The blower mounting plate can now be removed. Remove the four screws that secure the plate to the fi rebox base. 5. The blower is secured to the fi rebox. Disconnect the wire connectors before attempting to remove the blower from the fi rebox. 6. Remove the two screws securing the blower and lift through blower access opening. Note: When re-installing the replacement blower, it will be necessary to replace the gasket (W290-0104) on the blower mounting plate. FIGURE 41 BLOWER MOUNTING PLATE REMOVE 4 SCREWS REMOVE 2 SCREWS FIGURE 42 BATTERY REPLACEMENT 1. Remove the optional front. (Instructions on Pg. 17) 2. Tilt the control panel forward allowing access to the electode box which is screwed to the base of the fi rebox. (Fig. 43) BOWL BURNER CURVED DECORATIVE PANEL BURNER BOTTOM BURNER BASE SEE-THRU WINDOW ELECTRODE BOX (AA Battery Required) CONTROL PA NEL CONTROL PANEL FIGURE 43 Your comes equipped with a heat circulating blower. The blower is pre-wired and is controlled by the remote control supplied with the unit. For control details, see operation. Pg. 20. Drywall dust will penetrate into the blower bearings, causing irreparable damage. Care must be taken to prevent drywall dust from coming into contact with the blower or its compartment. Any damage resulting from this condition is not covered by the warranty policy. 1. Turn off the power to the fi replace. 2. Turn off the gas valve. BLOWER REPLACEMENT NIGHT LIGHTTM REPLACEMENT NIGHT LIGHTTM REPLACEMENT Yo u r comes equipped with our Night LightTM. The light has been pre-wired and is controlled from the remote control. If in the event the lamp or lens needs to be replaced, follow the instructions below. Unplug the wire harness / transformer from the junction box inside the fireplace or turn off the electrical breaker for the fi replace. FIGURE 44 SCREWS LENSE FRAME FIREBOX TOP FIGURE 45 AMBER SIDE UP GASKET LENSE FRAME FIGURE 46 Remove the four screws that secure the lens frame to the top of the firebox. This frame retains the glass lens. The lamp can now be accessed. Note: Do not handle the lamp (bulb) with bare fi ngers, protect with a clean dry cloth. The lamp will pull straight out of the socket. Replace with Wolf Steel parts only, as lamp and lens are special “high temperature” products. When re-installing, ensure integrity of gasket seal. THE FIREBOX MUST BE SEALED. Over tightening the screws could break the lens. “Light Leakage” from the upper area may be observed. The holes in the lamp housing are necessary for ventilation and must not be blocked. OPERATION / MAINTENANCE TIME OUT If the appliance is turned on and the Receiver does not receive any command for 24 hours, it automatically turns the appliance FIREPLACE OPERATION To operate this firplace using the remote, the pilot must be running and the gas valve turned to the “ON” position. Ensure that the receiver has power and the backup switch is in the auto position. FIGURE 46 1. Install the batteries (AAA) into the remote control transmitter. The “HOUSE” icon with room temperature will be displayed. 2. Press the ON/OFF button on the remote. Icons will appear at the same time and acoustic signal is generated if not, move the transmitter closer to the receiver and repeat. If a signal is still not heard, it will be necessary to execute the address setting procedure. Note: There maybe a few seconds delay before the receiver responds. Especially when using the wrought iron faceplate. 3. Fahrenheit -Celsius temperature indicator It is possible to set the Remote Control transmitter to display the temperatures in either Fahrenheit or Celsius. Use the UP or DOWN button on the transmitter until the cursor (small triangle) is left of the clock icon. 4. From time 0:00 press the LEFT key ten times. The display will show the transmitter address. Use the RIGHT button to toggle from °F to °C and vice versa. The display will show the selected unit of measure. Press the LEFT button ...
Otros modelos de este manual:Impresoras - TUREEN GD82NT-T (2.92 mb)