Votos - 2, Puntuación media: 3.5
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
– To clear the entered value, press the [No/C] key. 4 Press the [Start] key. This will start the copy cycle. – To stop copying before the set number of copies have been made, press the [Stop] key. bizhub 162/210 Making copies Making copies Loading paper While loading paper, be sure to observe the following precautions. Precautions Illustration If the paper is curled, flatten it before loading it. Do not load so much paper that the top of the stack is higher than the , mark or exceeds the specified number of sheets. Push the paper guides firmly up against the edges of the paper. When loading additional paper, remove any paper remaining in the drawer, place it on top of the new paper, and then align the paper in the stack well before loading it into the drawer. bizhub 162/210 Making copies Making copies 1 Pull out the 1st tray. ? Have the necessary precautions been observed when pulling out the tray? % Be careful not to touch the surface of the Paper take-up roller with your hands. 2 Press down on the paper-lifting plate until it locks into place. 3 Load the paper into the tray. ? Have the necessary precautions been observed when loading the paper? % Do not load so much paper that the top of the stack is higher than the , mark. 4 Slide the paper guides against the edges of the paper. ? Is the paper guide positioned correctly? % Make sure that the paper guides are pushed up against the edges of the paper. Paper take-up roller Paper-lifting plate bizhub 162/210 Making copies 5 Close the 1st tray. bizhub 162/210 Making copies Making copies Load paper into the 3rd, 4th and 5th paper trays using the same procedure described below. 1 Pull out the 2nd tray. 2 Press down on the paper-lifting plate until it locks into place. 3 Load the paper into the tray. ? Have the necessary precautions been observed when loading the paper? % Do not load so much paper that the top of the stack is higher than the , mark. 4 Slide the paper guides against the edges of the paper. ? Is the paper guide positioned correctly? % Make sure that the paper guides are pushed up against the edges of the paper. Paper-lifting plate bizhub 162/210 Making copies 5 Close the 2nd tray. bizhub 162/210 Making copies Making copies 4.3 Loading the document The document can be loaded into the document feeder (optional) or positioned on the original glass. Position the document correctly according to the type of document being copied. Loading documents into the document feeder 7 CAUTION Paper jam in fact of overloaded document feeder. % DF-502: A maximum of 50 document pages can be loaded. % DF-605: A maximum of 80 document pages can be loaded. % Do not load so many pages that the top of the stack is higher than the , mark. % Be sure to adjust the document guides so that they are against the edges of the document, otherwise the document may not be fed in straight. 1 Slide out the document guide plates. 2 Load the document pages to be copied face up into the document feeder. 4-10 bizhub 162/210 Making copies 3 Adjust the document guide plates to fit the size of the document. 4 Specify the desired copy settings. For details, refer to “Making a basic copy” on page 4-3. 5 Press the [Start] key. This will start the copy cycle. 2 Note Be sure to load the document correctly, otherwise the pages may not be fed in straight. bizhub 162/210 4-11 Making copies Making copies Use the following procedure to position plain paper or an original that is not suitable for use in the document feeder. 1 Raise the document feeder or original cover. 2 Place the document face down on the original glass. 3 Position the document on the scales above and to the left of the original glass. 4 Gently lower the document feeder or original cover. 5 Specify the desired copy settings. For details, refer to “Making a basic copy” on page 4-3. 6 Press the [Start] key. This will start the copy cycle. 4-12 bizhub 162/210 Making copies Making copies When making a copy from OHP transparencies, translucent paper, or other highly transparent original, position the original as detailed below. 1 Raise the document feeder or original cover. 2 Place the document face down on the original glass. 3 Position the document on the scales above and to the left of the original glass. 4 Place a blank sheet of paper of the same size over the document. 5 Gently lower the document feeder or original cover. 6 Specify the desired copy settings. For details, refer to “Making a basic copy” on page 4-3. 7 Press the [Start] key. This will start the copy cycle. bizhub 162/210 4-13 Making copies Making copies When copying an open book or magazine, position the original as detailed below. 1 Raise the document feeder or original cover. 7 WARNING Broken original glass by incorrect handling. % Do not place books weighing more than 3 kg on the original glass. In addition, do not press down extremely hard on the original, otherwise the machine may be damaged. 2 Position the book face down onto the original glass, with the top of th...
Otros modelos de este manual:Impresoras - BIZHUB 162 (2.68 mb)