Votos - 2, Puntuación media: 3.5
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
Allow extra space for opening covers and trays. The area should be well-ventilated and away from direct sunlight or sources of heat, cold, and humidity. Do not set the machine close to the edge of your desk or table. Clearance space • Front: 482.6 mm (enough space so that the paper tray can be removed) • Back: 100 mm (enough space for ventilation) • Right: 100 mm (enough space for ventilation) • Left: 100 mm (enough space for ventilation) Installing the toner cartridge 1 Open the front cover. 2 Remove the toner cartridge from its bag. Do not use a knife or other sharp object as it might scratch the drum of the toner cartridge. 3 Roll the toner cartridge 5 or 6 times to distribute the toner evenly inside the toner cartridge. Thoroughly rolling the toner cartridge will assure maximum copies per toner cartridge. 4 Remove the paper protecting the toner cartridge. NOTE: If toner gets on your clothing, wipe it off with a dry cloth and wash clothing in cold water. Hot water sets toner into fabric. 2.2 Getting started Getting started 2.3 CAUTION: • To prevent damage, do not expose the toner cartridge to light for more than a few minutes. Cover it with a piece of paper, if left exposed for more than a few minutes. • Do not touch the green underside of the toner cartridge. Use the handle on the toner cartridge to avoid touching this area. 5 Hold the toner cartridge by the handle. Slowly insert the toner cartridge into the opening in the machine. 6 Tabs on the sides of the toner cartridge and corresponding grooves within the machine will guide the toner cartridge into the correct position until it locks into place completely. 7 Close the front cover. Make sure that the front cover is securely closed. NOTE: When printing text at 5% coverage, you can expect a toner cartridge life of approximately 3,000 pages. (1,000 pages for the toner cartridge that is shipped with the machine.) 1 Groove 2 Tab Loading paper The paper input tray can hold a maximum of 250 sheets of 20 lb (75 g/m2) plain paper. 1 Pull open the paper input tray and remove it from the machine. 2 Fan the edges of the paper stack to separate the pages. Then tap the stack on a flat surface to even it up. 3 Insert the paper stack into the paper input tray with the side to be printed on facing down. NOTE: If you want to load a different sized paper, you need to adjust the paper guides. For details, see page 2.4. Getting started 2.4 4 Pay attention to the paper limit mark on both inside walls of the paper input tray. Paper overloading may cause paper jams. 5 Insert and slide the paper input tray back into the machine. NOTE: After you load paper, you need to set up your machine for the paper type and size you loaded. See page 3.6 for copying, or the Software Section for PC-printing. The settings made from the printer driver override the settings on the control panel. Changing the size of the paper in the paper input tray To load longer sizes of paper, such as Legal-sized paper, you need to adjust the paper guides to extend the paper input tray. 1 After pressing and unlatching the guide lock, slide the paper length guide out completely to extend the paper input tray to its full length. 2 After inserting paper into the paper input tray, squeeze the front paper length guide and slide it until it lightly touches the end of the paper stack. For paper smaller than Letter size, adjust the front paper length guide so that it lightly touches the paper stack. 3 Squeeze the paper width guide, as shown and slide it to the stack of paper until it lightly touches the side of the stack. NOTES: • Do not push the paper width guide far enough to cause the materials to warp. • If you do not adjust the paper width guide, it may cause paper jams. Making connections 1 Connect a USB cable to the USB connector on your machine. You need to buy a USB 2.0 compliant cable that is not longer than 3 m. 2 Connect the other end of the cable to the USB port on your computer. See your computer User’s Guide if you need help. To the USB port on your computer NOTE: When using the USB connection, your machine provides two USB modes; Fast and Slow. Fast is the default mode. Some PC users may experience poor USB function in the default mode. If this occurs, select Slow mode to achieve successful results. For details about changing the USB mode, 3 Squeeze the paper width guide, as shown and slide it to the stack of paper until it lightly touches the side of the stack. NOTES: • Do not push the paper width guide far enough to cause the materials to warp. • If you do not adjust the paper width guide, it may cause paper jams. Making connections 1 Connect a USB cable to the USB connector on your machine. You need to buy a USB 2.0 compliant cable that is not longer than 3 m. 2 Connect the other end of the cable to the USB port on your computer. See your computer User’s Guide if you need help. To the USB port on your computer NOTE: When using the USB connection, your machine provides two USB modes; Fast and Slo...
Otros modelos de este manual:Impresoras - SCX-4200 (3.24 mb)
Impresoras - SCX-4200R (3.24 mb)
Impresoras - SCX-4210 (3.24 mb)
Impresoras - Mono Multifunction Printer SCX-4200 Series (3.24 mb)