For detailed information about error message, see page 7.7. • The machine stops printing. At this stage, the toner cartridge needs to be replaced. Check the type of toner cartridge for your machine. (See "Supplies" on page 8.1.) 1 Turn the machine off, then wait a few minutes for the machine to cool. 2 Press the top cover lever, completely open the top cover. Grasp the handles on the toner cartridge and pull to remove the cartridge from the machine. 4 Take a new toner cartridge out of its package. Caution • Don't use sharp objects, such as a knife or scissors, to open the toner cartridge package. You could damage the surface of the toner cartridge. • To prevent damage, do not expose the toner cartridge to light for more than a few minutes. Cover it with a piece of paper to protect it if necessary. 5 Holding side edges of the toner cartridge, thoroughly rock it from side to side to redistribute the toner. 6 Place the toner cartridge on a flat surface, as shown, and remove the paper covering the toner cartridge. 6.5 Caution • Do not touch the green surface, the OPC drum or the front of each toner cartridge, with your hands or any other material. Use the handle on each cartridge in order to avoid touching this area. • If you leave the top cover open for more than a few minutes, the OPC drum can be exposed to light. This will cause damage to the OPC drum. Close the top cover should the installation need to be halted for any reason. Note If toner gets on your clothing, wipe it off with a dry cloth and wash it in cold water. Hot water sets toner into fabric. Insert the cartridge into place. Note If the top cover is not completely closed, the machine will not operate. Caution Be careful not to pinch your fingers, since the top cover is very heavy. Maintenance Parts To avoid print quality and paper feed problems resulting from worn parts, and to maintain your machine in top working condition the following condition, the following items will need to be replaced after the specified number of pages, or when the life span of each item has expired. Items Yield (Average) Transfer roller Approx. 50,000 pages Fuser unit Approx. 50,000 pages Paper feed roller Approx. 50,000 pages Hold the top cover and close it slowly and carefully, until the cover is the cover is securely latched. We highly recommend that this maintenance be performed by an authorized service provider, dealer or the retailer where you bought the machine. The warranty does not cover the replacement of the maintenance parts after their lifespan. 6.6 7 Troubleshooting This chapter gives helpful information on what to do if you encounter a problem. This chapter includes: • Tips for avoiding paper jams • Clearing paper jams • Understanding display messages • Solving other problems Tips for avoiding paper jams By selecting the correct media types, most paper jams can be avoided. When a paper jam occurs, follow the steps outlined on page 7.1. • Follow the procedures on page 4.5. Ensure that the adjustable guides are positioned correctly. • Do not overload the tray. Ensure that the paper level is below the paper capacity mark on the inside of the tray. • Do not remove paper from the tray while your machine is printing. • Flex, fan, and straighten paper before loading. • Do not use creased, damp, or highly curled paper. • Do not mix paper types in a tray. • Use only recommended print media. (see page 4.6) • Ensure that the recommended side of the print media is facing down in the tray. Clearing paper jams Refer to the table below to locate and clear the paper jam. Status display Explanation Solution In the paper feed area and rear the machine Clear the jam. (Page 7.1) Paper jam LED( ) blinks Rear and Inside the machine Clear the jam. (Page 7.3) In the exit area Clear the jam. (Page 7.5) Caution To avoid tearing the paper, pull the jammed paper out gently and slowly. Follow the instructions in the following sections to clear the jam. In the paper feed area and rear the machine If paper is jammed in the paper feed area and rear the machine, follow the next steps to release the jammed paper. 1 Press the tray open button. 2 Pull the tray open. 3 Remove the jammed paper by gently pulling it straight out as shown below. 7.1 7.2 4 Align the tray with the slot, and slide it into the machine. 5 Press the top cover lever, completely open the top cover. 6 Hold the top cover and close it slowly and carefully, until the cover is securely latched. Note If the top cover is not completely closed, the machine will not operate. Caution Be careful not to pinch your fingers, since the top cover is very heavy. 7 If the paper jam LED blinks, go to next step. 8 Open the rear cover. 9 Carefully take the jammed paper out of the machine. Caution Do not touch the fuser inside the machine. It is hot and could cause burns! The fuser's operating temperature is very hot. Take care when removing paper from the machine. 7.3 Otros modelos de este manual: Impresoras - ML-1630 (4.34 mb) Impresoras - ML-1631K (4.34 mb) Impresoras - Mono Laser Printer ML-1630 Series (4.34 mb)
