Votos - 3, Puntuación media: 4
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
6 Press the scroll button ( or ) until “Yes” displays and press the Enter button ( ). 7 Press the Upper Level button ( ), then use the scroll button ( ). 8 Press the Enter button ( ) when “IP Get Method” displays. 8.2 Using Your Printer on a Network 9 Press the scroll button ( or ) until “Static” displays and press the Enter button ( ). 10 Press the Upper Level button ( ), then use the scroll button ( ). 11Press the Enter button ( ) to access the IP Address menu. IP address consists of 4 bytes. Enter a number between 0 and 255 for each byte. 12 Press the scroll button ( or ) to enter a number between 0 and 255 and press the Enter button ( ). 13Repeat step 12 to complete the address from the 1st byte to the 4th byte. 14To select other parameters, such as Subnet Mask or Gateway, press the Upper Level button ( ), then use the scroll button ( or ). Press the Enter button ( ). 15Repeat steps 12 and 13 to configure the other TCP/IP parameters. 16Press the Upper Level button ( ) to return to ready mode. Dynamic Addressing (BOOTP/DHCP) To assign the TCP/IP address automatically by the server, take the following steps: 1 In ready mode, press the Menu button ( ) until you see “Network” on the bottom line of the display. Press the Enter button ( ) to access the menu. 2 Press the Enter button ( ) when “Config Network” displays on the bottom line. 3 Press the scroll button ( or ) until “Yes” displays and press the Enter button ( ). 4 Press the Upper Level button ( ), then use the scroll button ( ). 5 Press the Enter button ( ) when “Config TCP” displays. 6 Press the scroll button ( or ) until “Yes” displays and press the Enter button ( ). 7 Press the Upper Level button ( ), then use the scroll button ( ). 8 Press the Enter button ( ) when “IP Get Method” displays. 8.3 9 Press the scroll button ( or ) until “DHCP” displays and press the Enter button ( ). 10 To assign the address from the BOOTP server, press the Enter button ( ) when “BOOTP” displays. 11 Press the On Line/Continue button ( ) to return to ready mode. Configuring IPX Frame Types On IPX/SPX protocol networks (for example, Novell NetWare), the format of network communication frames must be specified on the printer. In most cases, you can keep the default setting “Auto”. However, you can manually set the frame type format, if required. • AUTO (default): Automatically senses and limits the frame type to the first one detected. • EN_8023: Limits the frame type to IPX over IEEE 802.3 frames. All others will be counted and discarded. • EN_II: Limits the frame type to IPX over Ethernet Frames. All others will be counted and discarded. • EN_8022: Limits the frame type to IPX over IEEE 802.2 with IEEE 802.3 frames. All others will be counted and discarded. • EN_SNAP: Limits the frame type to IPX over SNAP with IEEE 802.3 frames. All others will be counted and discarded. Note that the IPX/SPX protocol must be enabled in the Netware menu before you can configure frame types. See “Setting Network Protocols” on page 8.2. Take the following steps to change the frame type format: 1 In ready mode, press the Menu button ( ) until you see “Network” on the bottom line of the display. Press the Enter button ( ) to access the menu. 2 Press the Enter button ( ) when “Config Network” displays on the bottom line. 3 Press the scroll button ( or ) until “Yes” displays on the bottom line. Press the Enter button ( ). 4 Press the Upper Level button ( ). 5 Press the scroll button ( or ) until “Netware” displays on bottom line. Press the Enter button ( ). 6 Press the scroll button ( or ) until “On” displays on the bottom line and press the Enter button ( ). 7 Press the Upper Level button ( ), then use the scroll button ( ). 8 Press the Enter button ( ) when “Config Netware” displays. 9 Press the scroll button ( or ) until “Yes” displays on the bottom line. Press the Enter button ( ). 10 Press the Upper Level button ( ), then use the scroll button ( ). Using Your Printer on a Network 11Press the Enter button ( ) when “IPX Frame Type” displays. 12Press the scroll button ( or ) until you see the desired frame type and press the Enter button ( ). 13Press the On Line/Continue button ( ) to return to ready mode. Restoring the Network Configuration You can return the network configuration to its default settings. 1 In ready mode, press the Menu button ( ) until you see “Network” on the bottom line of the display. 2 Press the Enter button ( ) to access the menu. 3 Press scroll button ( or ) until “Default Set” displays on the bottom line. 4 Press the Enter button ( ) to confirm the selection. Rebooting the Network Interface Card If you configured the “Netware” or “Config WLAN” menu option, the printer will not recognize your change. In this case, you can simply reboot the network interface card without turning your printer off and back on. 1 In ready mode, press the Menu button ( ) until you see “Network” on the bottom line of the display. 2 Press scroll button ( or ) until “Reset Network” displa...
Otros modelos de este manual:Impresoras - ML-3560G (5.22 mb)
Impresoras - ML-3561N (5.22 mb)
Impresoras - ML-3561ND (5.22 mb)
Impresoras - ML-3561NDR (5.22 mb)