Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
Keep the rear cover opened during printing. • When selecting envelopes, consider the following factors: - Weight: should not exceed 90 g/m2 otherwise; jams may occur. - Construction: should lie flat with less than 6 mm curl and should not contain air. - Condition: should not be wrinkled, nicked, nor damaged. - Temperature: should resist the heat and pressure of the machine during operation. • Use only well-constructed envelopes with sharp and wellcreased folds. • Do not use stamped envelopes. • Do not use envelopes with clasps, snaps, windows, coated lining, self-adhesive seals, or other synthetic materials. • Do not use damaged or poorly made envelopes. 1 1 Pressure lever Media and tray 2. Learning the basic usage 35 • Be sure the seam at both ends of the envelope extends all the way to the corner of the envelope. 1 Acceptable 2 Unacceptable • Envelopes with a peel-off adhesive strip or with more than one flap that folds over to seal must use adhesives compatible with the machine’s fusing temperature for 0.1 second (about 170°C (338 °F)). The extra flaps and strips might cause wrinkling, creasing, or jams, and may even damage the fuser. • For the best print quality, position margins no closer than 15 mm from the edges of the envelope. • Avoid printing over the area where the envelope’s seams meet. Transparency To avoid damaging the machine, use only transparencies designed for use in laser printers. • Must withstand the machine’s fusing temperature. • Place them on a flat surface after removing them from the machine. • Do not leave unused transparencies in the paper tray for long. Dust and dirt may accumulate on them, resulting in spotty printing. • To avoid smudging caused by fingerprints, handle them carefully. • To avoid fading, do not expose printed transparencies to prolonged sunlight. • Ensure that transparencies are not wrinkled, curled, or have any torn edges. 1 2 Media and tray 2. Learning the basic usage 36 • Do not use transparencies that separate from the backing sheet. • To prevent transparencies from sticking to each other, do not let the printed sheets stack up as they are being printed out. Labels To avoid damaging the machine, use only labels designed for use in laser printers. • When selecting labels, consider the following factors: - Adhesives: Should be stable at your machine’s fusing temperature. Check your machine’s specifications to view the fusing temperature (about 170°C (338°F)). - Arrangement: Only use labels with no exposed backing between them. Labels can peel off sheets that have spaces between the labels, causing serious jams. - Curl: Must lie flat with no more than 13 mm of curl in any direction. - Condition: Do not use labels with wrinkles, bubbles, or other indications of separation. • Make sure that there is no exposed adhesive material between labels. Exposed areas can cause labels to peel off during printing, which can cause paper jams. Exposed adhesive can also cause damage to machine components. • Do not run a sheet of labels through the machine more than once. The adhesive backing is designed for only a single pass through the machine. • Do not use labels that are separating from the backing sheet or are wrinkled, bubbled, or otherwise damaged. Media and tray 2. Learning the basic usage 37 Card stock/ Custom-sized paper • In the software application, set margins at least 6.4 mm (0.25 inches) away from the edges of the material. Preprinted paper When loading preprinted paper, the printed side should be facing up with an uncurled edge at the front. If you experience problems with paper feeding, turn the paper around. Note that print quality is not guaranteed. • Must be printed with heat-resistant ink that will not melt, vaporize, or release hazardous emissions when subjected to the machine’s fusing temperature for 0.1 second (about 170°C (338°F)). • Must be non-flammable and should not adversely affect machine rollers. • Before you load preprinted paper, verify that the ink on the paper is dry. During the fusing process, wet ink can come off preprinted paper, reducing print quality. 2. Learning the basic usage 38 .... Setting the paper size and type 382. Learning the basic usage .... Setting the paper size and type After loading paper in the paper tray, set the paper size and type using the control panel buttons. • The settings set from the machine’s driver override the settings on the control panel. • For models that do not have the display screen on the control panel, this feature is not applicable. 1 1 Press (Menu) button on the control panel. 2 2 Press Paper > OK > Select the tray you want > OK. 3 3 Press Paper Size > OK > Select the option you want > OK. 4 4 Press Paper Type > OK > Select the option you want > OK 5 5 Press (Cancel) to return to ready mode. If you want to use special-sized paper such as billing paper, select Custom in the Paper tab in the Printing Preferences (see "Opening printing preferences" on page 41). Basic printing 392. Learning the basic us...
Otros modelos de este manual:Impresoras - ML-3750ND (13.08 mb)
Impresoras - ML-3750ND/ALG (13.08 mb)
Impresoras - ML-3750ND/SAU (13.08 mb)
Impresoras - ML-3750ND/TED (13.08 mb)