Votos - 1, Puntuación media: 5
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
NO. FA7-3911-010 Printed in Thailand Label Remove the shipping attachment on the left side using a coin. Otherwise the scanning unit of the machine is locked and you cannot make copies or send faxes. Slide left until the |< mark appears. Insert the removed shipping attachment in the holder. Keeping the cartridge cover open, go to section 2 - INSTALL CARTRIDGE Keep the shipping attachment in the holder in case you need to transport the machine. REMOVE ALL SHIPPING MATERIALS 2 11 Lift the platen unit lever (1) and slide the platen unit (2) Open the cartridge cover. A E B C D Grasp the cartridge with one hand, firmly and slowly pull the sealing tape tab with the other hand. Remove the sealing tape completely. Remove the new cartridge from its bag. 2 INSTALL CARTRIDGE Place the cartridge on a flat and stable surface, grip the sealing tape tab and snap in the direction shown. Make sure that the tab is detached from the cartridge. Rock the cartridge 5 or 6 times to distribute the toner evenly. Position the arrow mark on the cartridge towards the inside of the machine, and gently slide the cartridge in the machine as far as it will go. Close the cartridge cover and slide the platen unit to the original position. A B C D E F Grip the cassette handle, and pull out towards you until the cassette comes to a stop. Load the paper stack beneath the cassette’s length guide (1) and width guide’s claws (2). Make sure that the paper stack does not exceed the length and width guide’s claws in the cassette. Failure to do so will cause a paper jam. Gently insert the cassette as far as it will go. Hook the tab on the output tray onto the opening on the machine. 3 LOAD PAPER A B C Connect the supplied power cord to the power cord connector on the left side of the machine. CONNECTING USING PARALLEL CABLE or CONNECTING USING USB CABLE CONNECTING THE POWER CORD When the power cord is plugged into the machine and into the wall outlet, the machine is turned on. The LCD displays PLEASE WAIT. Please wait until the LCD returns to the Copy Mode standby display. Connect the supplied power cord to the power cord connector on the left side of the machine. Then connect the other end into a properly grounded 120 VAC three-prong outlet. Copy Mode standby display 4 CONNECTIONS PAR USB connection CCoonnnneecctt ttoo yyoouur rc coommpuptuetre urs uinsgin UgS UBS cBab clea.ble. USB interface connection. PARALLEL Parallel interface connection Connect to your computer using parallel cable. Fix the connector solidly using the wire clips. Parallel interface connection Connect to your computer using parallel cable. Make sure the computer is turned off. SET FAX RECEIVE MODE (D680) 5 Press FAX to switch the machine to Fax Mode. Press RECEIVE MODE until the mode you want appears: ex. RECEIVE MODE Manual You can select from the following: FAX ONLY: if you use your machine to receive only faxes. DRPD: to distinguish between fax and voice calls by using Distinctive Ring Patterns. MANUAL: when a telephone is connected to the machine, you can receive faxes by pressing START before replacing the handset on the telephone. AnsMode: if you want to receive faxes automatically and route voice calls to an answering machine. FaxTel: when a telephone is connected to the machine, the machine automatically switches between faxes and voice calls. ex. FAX 06/20/2001 17:08 Manual STANDARD Press SET. The selected receive mode is set and the machine returns to standby mode. The current date and the selected receive mode are displayed. • The machine does not ring when it receives a fax in FaxOnly. If you want to be alerted when a fax is received, connect a telephone to the machine, and enable the INCOMING RING setting. (---> Fax Guide) • For AnsMode, you need to connect an answering machine or a telephone with an answering machine to your machine (see below). • Follow these guidelines when using the machine with an answering machine: — Set the answering machine to answer on the first or second ring. — When recording the outgoing message on the answering machine, the entire message must be no longer than 15 seconds. CONNECTING THE TELEPHONE LINE AND AN EXTERNAL DEVICE (Only for the D680 model) The machine has two jacks on the left side for connection of the following: L : Telephone Line : External device, such as telephone or answering machine. 2. When you require to send and receive both faxes and voice calls, connect the line from the telephone or answering machine to the Jack. 1. Connect the supplied telephone line to the Jack, then connect the other end of the line to the telephone jack on your wall. L CONNECT EXTERNAL DEVICES AS FOLLOWS: • Telephone or answering machine L Telephone or Telephone answering machine Machine line • Telephone and answering machine L LINE TEL Telephone Telephone Answering Machine machine line • Telephone and modem L Machine Modem LINE TEL Computer Serial Connector Telephone Telephone line • Built-in computer modem and telephone L LINE TEL Computer...