Votos - 4, Puntuación media: 3
(
)
)
|
Resumen del manual
READ THIS SHEET FIRSTREAD THIS SHEET FIRST Unpack the machine and its components. Check that you have the following: . Machine . Multi-purpose tray . Tray cover . Paper output tray . Ink tanks . Printhead (Black, cyan, magenta, yellow) . Power cord . Documentation (Set-Up Sheet, Basic Guide, Extended Service Plan, Registration Card) . PCMCIA card adapter . MultiPASS Suite software CD-ROM NOTE • A printer cable is not included. You must purchase a USB cable (less than 16.4 ft./5 m) to connect your machine to a computer. Remove the shipping material from the machine. 1 Place the machine on a flat surface. 2 Remove all shipping tapes from the exterior of the machine. NOTE • DO NOT remove the USB label A at this stage. Assemble the machine. Top rear view of attachment slots 2 Hook the center tab on the paper output tray to the center opening, then lower the tray. 1 Attach the multi-purpose tray. USB label A Load paper. Place a stack of paper (print side up) in the multi-purpose tray q and adjust the paper guide A to the width of the stack w.Make sure the stack does not exceed the paper limit mark B.Then place the tray cover C over the multi-purpose tray. Connect the power cord. ON/OFF(1sec.) PLEASE WAIT PUT IN CARTRIDGE Approx. 30 seconds 1 Plug the power cord into a socket. 2 When you connect the machine, the Alarm light blinks, and the messages below should appear in the LCD. 3 If nothing appears in the LCD, press [ON/OFF (1 sec.)] to turn on the machine. •If you need to turn off the machine, press [ON/OFF (1 sec.)] for one second. q w B C A ON/OFF(1sec.) PLEASE WAIT PUT IN CARTRIDGE Approx. 30 seconds 1 Plug the power cord into a socket. 2 When you connect the machine, the Alarm light blinks, and the messages below should appear in the LCD. 3 If nothing appears in the LCD, press [ON/OFF (1 sec.)] to turn on the machine. •If you need to turn off the machine, press [ON/OFF (1 sec.)] for one second. q w B C A Install the printhead. IMPORTANT • To turn off the machine, be sure to always press [ON/OFF(1sec.)].This will ensure that the printhead is capped and prevent it from drying up. • If you are not using the machine for a long period of time,we recommend that you print (in black and color) or clean the printhead approximately once a month to maintain the printhead in good working condition. 1 Press [Open] qand lift up the scanning unit w. Then remove the tape A. IMPORTANT • Do not touch the metal rod or any parts inside the machine. • Do not turn off the machine when opening the scanning unit. 2 Remove the printhead from its packaging, then remove the orange protective capB. IMPORTANT • Do not touch the electrical contacts C. 3 Raise the lock lever D, then gently slide the printhead into the holder. Lower the lock lever. IMPORTANT • Do not touch the lock lever once the printhead has been installed. D C B A q w Turn over to continue Install the ink tanks. 1 Start with the yellow ink tank. Pull the orange tape in the direction of the arrow and remove the plastic wrapper so you can see the air hole A. Turn the ink tank over so that the protective cap Bis facing up.Then hold the ink tank as shown below and remove the protective cap B. NOTE • To avoid spilling ink, never press on the long sides of the ink tank C. • Once you remove the protective cap B, do not touch the ink port D. 2 Insert the ink tank (label-side up) into the correct slot (refer to the color guide on the printhead). Press down gently on the ink tank until an audible click is heard. 3 Repeat steps 1 and 2 to install the remaining magenta, cyan, and black ink tanks. 4 Close the scanning unit until it locks into place. Be sure to now align the printhead as explained in step 8. PUSU Yellow Made in Japan Ink Tank BCI-3eY PULL PULL BCI-3eY Ink Tank A B B D C Align the printhead. NOTE • If you will be installing the MultiPASS Suite software, you can also align the printhead from the software. For details, see p. 10-8 of the Basic Guide. 1 When the LCD displays the following, press [Set]. The machine will print a horizontal line pattern, and the LCD will display: 2 In column A on the printout, note which box has the most solid image. Note the value next to this box and use [2] or [3] on the operation panel to enter it. Then press [Set]. 3 Repeat step 2 for columns B to F. 4 When values for all columns have been entered and the LCD displays the following, press [#] to return to standby mode. NOTE • If streaks appear on the printed surface when you use the machine, perform the vertical printhead alignment. For details, see p. 10-7 of the Basic Guide. 1234560# 789.... A Most solid box Least solid box BAD SAMPLE GOOD SAMPLE Column A Value for column A .. ALIGN PRINT HEAD PRESS SET KEY 1234560# 789.... A Most solid box Least solid box BAD SAMPLE GOOD SAMPLE Column A Value for column A .. ALIGN PRINT HEAD PRESS SET KEY Install the software. IMPORTANT • DO NOT connect the USB cable before installing the software. NOTE • When installing the softwa...