Votos - 4, Puntuación media: 4.3
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
For EAN-13 and EAN-8, the check digit is appended at the end of the printed digits. *2 The number of digits printed below a bar code equals the input characters plus automatically appended characters. *3 An error message is displayed whenever there are insufficient digits. The unit will not allow input of too many digits. Troubleshooting • Printing • Power Supply Nothing appears on the display. Possible Causes Action Page Low batteries Replace batteries. E-6 Improper display contrast setting Adjust display contrast. E-8 Batteries loaded incorrectly Remove batteries and reload them correctly. E-7 AC adaptor is not connected correctly. Make sure the AC adaptor is connected correctly. E-7 • Text Input Cannot input text. Possible Causes Action Page FUNC key has been pressed. Press ESC to clear FUNC key operation. E-9 Tape does not come out when PRINT is pressed. Possible Causes Action Page Tape cartridge compartment cover is not closed completely. Securely close the cover. E-8 No more tape left in the cartridge. Replace the tape cartridge with a new one. E-8 Tape jam Remove the tape cartridge and pull out the jammed tape by hand. Cut off excess tape with scissors, and carefully replace the cartridge into the label printer. Important! Never allow the tape outlet to become blocked and never touch tape as it is being fed during printing. E-8 Tape comes out when PRINT is pressed, but nothing is printed on it. Possible Causes Action Page Only blank spaces were input. Input the text you want to print. E-9 Printing is blurred, blotched, broken, etc. Possible Causes Action Page Improper print density setting Adjust the print density setting. E-17 Improper loading of the cartridge Remove the tape cartridge and reload it correctly. E-8 Dirty printer head or rubber roller Clean the printer head and roller. E-20 •Using Labels Ink ribbon is being fed from the tape outlet along with the tape. Possible Causes Action Page Tape cartridge loaded while the ink ribbon is slack. Remove the tape cartridge and check to make sure the ink ribbon is not broken. Next, take up any slack in the ink ribbon and then reload the tape cartridge. Important! • Before loading a tape cartridge into the label printer, always make sure you take up any slack in the ink ribbon first. • If the ink ribbon is broken, you must change to another tape cartridge. E-8 Label will not adhere to a surface. Possible Causes Action Page The backing paper is still on the back of the tape. Peel the backing paper from the back of the tape to expose the adhesive. E-16 Surface is unsuitable for affixing a tape. Labels do not adhere well to surfaces that are rough, wet, oily, or dirty. E-16 Error Messages/Display Messages • Tape Cutting Message Possible Causes Action . ERROR! • The number carriage returns you input causes • Use wider tape or reduce the number of lines. * This message the label to exceed the 6mm tape...1 line appears on the maximum number of lines 9mm tape...1 line screen for about for the tape you are 12mm tape...Up to 2 lines one second. using. • You are attempting to print a stamp while three lines of text are input. 18mm tape...Up to 3 lines • Reduce the number of lines of text to two. NO DATA! * This message appears on the screen for about one second. • You are attempting to recall text from memory when there is none stored. OVERWRITE? • You are attempting to • Press SET to overwrite SET/ESC store text in memory when it already containes text. the existing text with the new text, or ESC to cancel the store operation. Cannot cut tape. Possible Causes Action Page Tape cutter blade is dull. Take the label printer to the dealer from whom you purchased it to have the tape cutter blade replaced. — Printed text is cut off by tape cut operation. Possible Causes Action Page Out of tape Replace the tape cartridge with a new one. E-8 Message Possible Causes Action TAPE ERROR • You are attempting to perform printing without setting a tape cartridge. • You are attempting to print a stamp using a tape size other than 18mm. • You are attempting to perform a bar code operation using a 6mm or 9mm tape. Press any key besides ON/OFF to clear the error message. • Turn the power OFF and set the tape cartridge. • Use only 18mm tape to print a stamp. • Use only 12 or 18mm tapes to perform bar code operation. LENGTH ERROR! * This message appears on the screen for about one second. • You are attempting to print a stamp with text that is longer than 5.5cm. • Shorten the text you are printing and try again. LOW BATTERY • Battery power is low. • Replace the batteries. DATA ERROR! • Data in memory has become corrupted for some reason. • Press any key besides ON/OFF to clear the error message. In response to the “INITIAL?” message that appears, press SET to initialize the Label Printer. DIGIT ERROR! * This message appears on the screen for about one second. Input of the wrong number of digits for a bar code operation. Input the correct number of digits for the type of bar code you...