Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
Each numeral and symbol on the key buttons in the table above is backlit. 11 RS-232C Interface Connector (IT-3100M53E/ M54E) For connection of a bar code reader and so forth. Connect by opening the connector cover. 12 Program Key (R) This key can be assigned any function available. IT-3100M55E/IT-3100M55U/IT-3100M56E/IT-3100M75E The default settings are as follows. This key is used to read bar codes and 2D codes. 13 Power Jack The AC adaptor is connected to this jack when charging the lithium ion battery pack. Open the jack cover to connect the AC adaptor. 14 IR Port This is used for IR data communication with another Handheld Printer Terminal or with the Bridge Satellite Cradle. General Guide 15 Battery Pack Cover Lock Switch Turn this switch when opening and closing the battery pack cover. 16 Battery Pack Cover Houses the battery pack inside. 17 PC Card Slot For connection of a separately sold PC card. Remove the cover to install a PC card. 18 Hand Strap Hook Hook the hand strap here. 19 14-pin Serial Interface Connector Provided for future use. 20 Power Terminals Terminals for supplying power from the Bridge Satellite Cradle and Cradle-type Battery Charger. 21 Neck Strap Hooks Hook the neck strap here. 22 Magnetic Card Reader (IT-3100M54E/ M55E/M55U/ M75E) Magnetic cards are read by passing through this magnetic card reader. Remove the cover to use. 23 Reset Switch Press to reset the Handheld Printer Terminal. Be careful not to press by mistake. 24 Screen Protect Cover Mounting Remove the screws when attaching the Screen Protect Cover. 25 C-MOS Imager (IT-3100M55E/ M55U/M56E/ M75E) Reads 1D bar code symbologies and stacked 2D code symbologies. Key Functions Key Functions 1 Fn Key This key is used to switch the character input mode or make various settings in combination with other keys, or start up a pre-registered application. 2 Numeric Keys These keys are used to input numbers and letters. 3 (Cursor Key) Moves the cursor to the left. 4 (Cursor Key) Moves the cursor to the right. This is also used to feed paper when pressed after pressing the Fn key when printing paper is loaded. 5 -This key is pressed when inputting a hyphen or bar. 6 . This key is pressed when inputting a decimal point. 7 C This key is pressed when canceling an operation and input. 8 BS This key is pressed when deleting the character to the left of the cursor. 9 ENT This key is pressed when entering an input. * Each numeral and symbol on the key buttons in the table above is backlit. Replacing the BatterReplacing the Battery Your Handheld Printer Terminal uses two types of battery: a battery pack and a memory backup battery. A battery pack (DT-9723LIC) is used for the main battery. A backup battery is housed inside the Handheld Printer Terminal. This guide uses the following terms to refer to the batteries. Battery Pack: Rechargeable battery pack for normal operations and data storage Backup Battery: Built-in battery for memory backup When the battery pack power goes low, immediately charge it or replace it with a charged battery pack. For information how to charge battery pack, see pages 49, 56 and 60. Replacing the Battery Pack Important! Always keep backup copies of all important data! • The main battery powers normal operation and also provides power required to maintain memory contents, while the backup battery provides backup power to maintain memory contents. Because of this, you should not remove the main battery while the backup battery is dead. Removing the battery pack while the backup battery is dead causes data in the memory to be corrupted or lost. Note that once data is lost it cannot be recovered. Always keep separate backup copies of all important data. • The charge of a battery pack when you purchase it may be depleted due to testing at the factory or natural discharge during shipment and storage. Be sure to charge the battery pack before you use it. • The life of a battery pack is limited, and charging a battery pack causes it to gradually lose its ability to maintain the charge. If your battery pack seems to require charging very frequently, it probably means it is time to purchase a new one. • A fully charged backup battery can maintain memory (RAM) contents for about 10 minutes, even when the main battery is removed. • The backup battery achieves a full charge in about four days when the battery pack is loaded. To replace the battery pack 1. Make sure that the Handheld Printer Terminal is turned off. If the power is on, press the power key to turn it off. 2. Turn the battery pack cover lock switch on the side of the Handheld Printer Terminal to the “FREE” position. 3. Open the battery pack cover. 4. Remove the battery pack. Press down the battery pack eject button (see the arrow). Remove the battery pack by pulling on the tape. 5. Install a charged battery pack in the Handheld Printer Terminal. Make sure the battery pack is aligned correctly when you install it. Replacing the Battery 6. Return the battery pack co...