Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
• Loading the ink ribbon cassette while the ink ribbon is slack creates the risk of malfunction. Rotate in the direction of the arrow. – 22 – 4. Load the ink ribbon cassette into the printer. • Make sure that the ink ribbon passes between the print head the rubber roller as shown in the illustration below. Press down on the ink ribbon cassette until you hear them click securely into place. Make sure these lines are parallel. Important! • Installing the ink ribbon cassette incorrectly or failing to secure them properly in place can cause the ribbon to break. 5. Close the cassette cover. • Press down on the cassette cover until you hear it click securely into place. To remove the ink ribbon cassette 1. Open the cassette cover. 2. Grasping both sides of the ink ribbon cassette, lift it straight up. Storing a Partially Used Ink Ribbon Cassette Install a stopper on the partially used ink ribbon cassette, place the cassette into its plastic bag, and then into its box. Store it where it will not be exposed to dirt and dust. Number of Prints Per Ink Ribbon Cassette Upper label • Upper or Lower Label Only: Approximately 40 prints • Upper and Lower Label: Approximately 20 Lower label prints – 23 – Inserting a Disc into the Printer See the DISC TITLE PRINTER Application User's Guide for information about how to insert a disc into the printer for printing and how to use the positioning guide. Caring for the Printer A dirty print head can make it impossible to obtain good printing results. Perform the following steps to clean the print head when it becomes dirty. Important! • Use only a cotton swab or some other soft material to clean the print head. 1. Open the cassette cover. 2. Unplug the USB cable from the PC and printer. 3. Unplug the power cord from the wall outlet, and then unplug the AC adaptor from the printer. 4. Use a cotton swab moistened with alcohol to clean the print head. You can use a commercially available cassette tape recorder head cleaning kit to clean the print head. Cleaning the Printer Exterior Clean this part of the print head. Print head Wipe the exterior of the printer with a cloth moistened with plain water. Wring all excess liquid from the cloth before wiping the printer. Never use benzene, alcohol, thinner, or other volatile agents to clean the printer exterior. Doing so can damage the case. – 24 – Troubleshooting Consult this troubleshooting guide whenever you start to have problems with the printer. If you cannot find the solution to your problem below, contact your original retailer. Symptom Possible Cause Recommended Action I can't get a connection between the printer and a computer. The bundled USB cable or the AC adaptor is not connected properly. Re-connect the cable and the AC adaptor properly. The USB driver is not installed correctly. Unplug the USB cable and the plug it back in again. Though the USB driver is Try using a different USB port on installed correctly, data your computer, or try using a communication is not different USB cable. possible for some reason. The printing operation is finished normally, but nothing is printed. The ink ribbon is used up. Load a new ink ribbon cassette (option). Printing is not clear. Printing is poor quality. Printing is too light. Any of the following can interfere with proper printing. • A disc printing surface that is not smooth and flat • A disc printing surface that has a design or lines printed on it • A disc printing surface that supports ink jet printing only Use a disc that meets the requirements described in the bundled “Printing Precautions” or at the following Internet URL. You can also try adjusting the print density to make it darker. (See the DISC TITLE PRINTER Application User's Guide) The ink ribbon cassette is not loaded properly. Re-load the ink ribbon cassette properly. The printed The color of the final Try using a lighter color disc or a color is printout is affected by darker color ink ribbon. different from both the color of the ink the ink ribbon ribbon and the color of color. the disc you are printing on. – 25 – Symptom Possible Cause Recommended Action The printing is not positioned correctly on the disc. Improper alignment of the disc when it is placed in the printer. Use the positioning guide when aligning the disc. (See the DISC TITLE PRINTER Application User's Guide) The disc stops part way through printing. The power cord plug or the AC adaptor is not plugged in as far as it will go. Correctly connect the power cord and the AC adaptor. The printer is malfunctioning. If you cannot easily remove the disc from between the print head and roller, refer to the "General Guide" explanation on page 17. Printing will not start. The disc is not positioned correctly in the printer. Remove the disc and then reinsert it straight into the left side of the slit along the top of the printer. (See the DISC TITLE PRINTER Application User's Guide) I can't remove a disc from the printer. The printer...