Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
Disclaimer . Refer to this product’s User Manual for detailed information and instructions. You can download the User Manual from the CHAUVET® website: . Read ALL the disclaimers and Safety Notes in this document, as well as those in the product’s User Manual before installing, operating, or maintaining this product. Safety Notes . DO NOT open this product unless instructed. It contains no user serviceable parts. . DO NOT look at the light source when this product is on. . DO NOT touch the product when it is operating because it may be hot. . DO NOT cover the ventilation slots when the product is operating to avoid internal overheating. . DO NOT install or operate this product where there is less than 50 cm to the nearest surface to allow adequate ventilation around it. . DO NOT leave any flammable material within 50 cm from this product while operating or connected to the power outlet to minimize the risk of fire. . DO NOT carry this product from the head. Use the handles instead. . DO NOT mount this product overhead without using a safety cable. . DO NOT operate this product outdoors or in any location where dust, excessive heat, water, or humidity may affect it. . DO NOT operate this product if you see damage on the housing, lenses, or cables. In any of these cases, have the damaged parts replaced by an authorized technician at once. . DO NOT connect this product to a dimmer or rheostat. . ONLY connect this product to a grounded and protected circuit. What Is Included . One Q-Wash 560Z-LED . One IEC Power Cord with Edison Plug (US market) . One Safety Cable . Two Omega Brackets . Warranty Card . Quick Reference Guide Q-Wash_360Z-LED_-_Mounting_A_01.gif Floor Mounting Overhead Mounting C Clamps (not included) Safety cable (included) Omega brackets (included) Q-Wash_360Z-LED_-_Mounting_B_01.gif Features . 12 or 15-channel RGBWA LED moving yoke wash product . Pan: 540. . Tilt: 270. . RGBWA color static mixing with or without DMX control . Vector speed channel for RGBWA color mixing . Variable zoom . Variable electronic strobe . Continuously variable electronic dimmer (0~100%) . Built-in automated programs . Remote product reset and vector speed channel . 255-step fully customizable program . Recall auto or custom programs via control panel or DMX . Color temperature presets (3,200~10,000 K) AC Power This product has an auto-ranging power supply that works with an input voltage range of 100~240 VAC, 50/60 Hz. Fuse Replacement 1. Disconnect the unit from the power outlet. 2. With a flat head screwdriver, wedge the fuse holder out of the housing and remove the blown fuse from the holder. 3. Replace the blown fuse with a fuse of the exact same type and rating. 4. Insert the fuse holder back in place and reconnect the power. Mounting Before mounting this product, read the Safety Notes at the beginning of this guide and on page 2 of the product’s User Manual. Then, follow the mounting procedure indicated in the Setup chapter of the User Manual. Product Mounting Diagram Menu Options 1st Level 2nd Level 3rd Level Description INTRO ADDRESS 001~512 Selects a starting DMX address RESET NO/YES Resets the product’s custom settings FAN HIGH Select the fan’s operation mode. NOTE: Product’s controller will force the fan to High if the product’s internal temperature becomes too high, despite any manual or DMX setting NORMAL LOW AUTO RUN DMX512 Selects DMX running mode AUTO 1 Selects the first automatic program AUTO 2 Selects the second automatic program CUSTOM Selects the user customizable program SLAVE Selects the Slave running mode TEST Starts the product’s test sequence CHANNELS BASIC Selects the 11-channel DMX mode ADVANCED Selects the 15-channel DMX mode DISPLAY 60 CLOSE Turns off the display after 60 seconds BRIGHT Keeps the display on KEYLOCK NO/YES Activates/deactivates the control panel password DIMMER DIMMER 4~1 Slow (DIM 4) to fast (DIM1) dimmer curves DIMMER 0 Linear dimmer INFO EDITION Shows the version of the installed S/W INVERT Pan NORMAL/ REVERSE Defines the pan direction Tilt Defines the tilt direction Dimmer Defines the direction of the dimmer fader Use NO/YES Activates the changes RANGE P/Start 000~255 Sets the pan start point (restricted range) P/Finish Sets the pan end point (restricted range) T/Start Sets the tilt start point (restricted range) T/Finish Sets the tilt end point (restricted range) Use Activates the changes SPECIAL Black delay NO/YES Activates the move-in black delay (3 s) Reset DMX The DMX controller can reset the product SYSTEM The control panel can reset the product Power NORMAL/ HIGH LEDs illuminate at normal or high intensity NOTE: Product will return to Normal if temperature becomes too high Color UC White output matches that of older products RGBTOW White output set by RGB-W OFF White output defined by RGBW faders Fan DMX The DMX controller can set the fan speed SYSTEM The control panel can reset the fan speed EDIT STEP 000~255 Selects the program step PAN Sele...