Votos - 4, Puntuación media: 3.5
(
)
)
|
Resumen del manual
Cartridges are vacuum packed to maintain reliability. Canada only: For French speakers, remove the sticker from the backing sheet and place it on the right side of the control panel. Remove all protective materials from the printer, including from inside the paper cassette. 1 Raise the scanner and remove the transportation lock. 2 Store the transportation lock as shown. 3 Lower the scanner. 1 Unpack Start Here (Included for Canada only) 1 Connect the power cable. Caution: Do not connect to your computer yet. 2 Turn on and adjust Phone cord Power cord Series 3 Make settings 1 Select your language and country. Touch the screen to select the desired option. Press or to see more countries. 2 For the Daylight Saving Time setting, select Summer if your region uses Daylight Saving Time and it’s currently in effect. (DST is effective from spring through summer.) Otherwise, select Winter to turn off the setting. Press OK. 3 Select the date format. 4 Use the numeric keypad to set the date, then press OK. 5 Select the time format. 6 Use the numeric keypad to set the time. 7 Press OK when done. Note: You can change the date and time settings by pressing the Home button, selecting Setup, selecting Printer Setup, then Date/Time. For more information on using and adjusting the control panel, see your Quick Guide. 2 Press the On button, then raise the control panel. To lower the control panel, press the Unlock button. Caution: To avoid damaging your Artisan 810 Series, always press the Unlock button to lower the control panel. 5 Load paper 4 Install ink cartridges Note: Do not load paper yet. 1 Lift up the scanner. 2 Unpack the ink cartridges. 3 Remove only the yellow tape from each cartridge. Caution: Don’t remove any other seals or the cartridges may leak. 4 Insert the cartridges in the holder for each color. Press each cartridge down until it clicks. 5 Lower the scanner. 6 Wait while ink charges. Charging takes about 5 minutes. Note: Your Artisan 810 Series ships with full cartridges and part of the ink from the first cartridges is used for priming the Artisan 810 Series. Replacement cartridges will print more pages. Caution: Don’t turn off the Artisan 810 Series while the ink system is initializing or you’ll waste ink. The paper cassette has 2 trays. The main tray is for letter-size, legal-size, or 8 x 10-inch paper. The photo tray is for 4 x 6- or 5 x 7-inch photo paper. 1 Pull out the paper cassette. Then slide back the photo tray and lift it up. 2 Squeeze the edge guides and slide them out. Then insert paper with the glossy or printable side face-down. 3 Slide the edge guides against the paper. 4 Lower the photo tray. 5 Squeeze the edge guides and slide them out. Then insert 4 x 6-inch or 5 x 7-inch photo paper with the glossy or printable side face-down. Note: Make sure the paper fits under the edge guides. 6 Slide the edge guides against the paper. 7 Keep the cassette flat as you insert it. 8 Extend the output tray and flip up the stopper. Network (wireless or wired) See your Network Installation Guide. You can’t install your software as described below. OR USB connection Make sure you have a USB cable (not included). Then follow the steps below. USB connection Follow these steps to connect the Artisan 810 Series directly to your computer using a USB cable (not included). Windows® 1 Make sure the Artisan 810 Series is NOT CONNECTED to your computer. Note: If you see a Found New Hardware screen, click Cancel and disconnect the USB cable. You can’t install your software that way. 2 Insert the Artisan 810 Series software CD. With Windows Vista®, if you see the AutoPlay window, click Run Epsetup.exe. When you see the User Account Control screen, click Continue. 3 Click Install and follow the on-screen instructions. To use the Artisan 810 Series for faxing, connect the included phone cord from a telephone wall jack to the LINE port on the Artisan 810 Series. To connect a telephone or answering machine, see the Quick Guide for instructions. Note: If you’re connecting to a DSL phone line, you must use a DSL filter or you won’t be able to fax. Contact your DSL provider for the necessary filter. 6 Connect the phone cord 7 Choose your connection 4 When you see this screen, select Install driver for direct USB connection and then click Next. 5 When prompted, connect a USB cable. Use any open USB port on your computer. Note: If installation doesn’t continue after a moment, make sure you securely connected the USB cable and turned on the Artisan 810 Series. 6 Follow the on-screen instructions to install the rest of the software, set up your fax header, and register your Artisan 810 Series. Be sure to register your Artisan 810 Series to receive these great benefits: 2-year limited warranty and 2-year toll-free customer support.* 7 When you’re done, remove the CD. You’re ready to go! Enjoy your Artisan 810 Series! See your Quick Guide or online Epson Information Center for instructions. Macintosh® 1 Make sure the Artisan 810 Ser...