Votos - 4, Puntuación media: 3.8
(
)
)
|
Resumen del manual
ADJUSTABLE ("CRESCENT") WRENCH _ PIPE WRENCH HACK SAW TROUBLE-FREE CARE AND USE. WILL HELP YOU. have no trouble making a first-rate installation. NOTE: Read through the entire guide before you start installation so you can get all the tools and materials you will need with one trip to the store. These are the tools and materials you may need. _ AUGER DRAIN SWITCH 120 amp, rating)/_,_" ON- OFFELECTRICAL _ HAMMER ELECTRICAL CABLE CONNECTOR (1/2inch) DISHWASHER / DRAIN CONNECTIN o oI / COPPER WIRE WIRE NUTS HOSE CLAMP PLUMBER'S PULP( (2 -Size 54) (7_inch) (12 or 14 gauge ) (% lb.) WP71865 INSTALLATION DIMENSIONS AI DRAWING REPRESENTATIVE OF A FOOD WASTE DISPOSER IMPORTANT:PLUMB WASTELINE TO PREVENTSTANDING WATERINDISPOSERMOTORHOUSING. NOTE: Please refer to the dimensions which match your disposer model number. B" -DISTANCE FROM BOTTOM OF SINK TO CENTER LINE OF DISPOSER OUTLET, ADD 1/2"WHEN STAINLESS STEEL SINKS ARE USED, E" -LENG'R,_ OF DISCHARGE TUBE FROM " CENTER UNE OF DISPOSER OUTLET TO END OF DISCHARGE TUBE. OKAY, LET'S START THE INSTALLATION ONE STEP AT A TIME. b AND MAKE SURE EVER,..YTHING IS THERE. (your new CHECK THE PARTS AGAINST THE DRAWINGS BELOW disposer may not look hke the one pictured.) THE MOUNTING ASSEMBLY CONSISTING OF: Sink sleeve (__/' _oie_ing _/o_17 ° "WRENCHETTE" Fiber gasket (1/4INCH HEX WRENCH) Back-up ring _ _) SE( F-SERVICE DISCHARGE TUBE, GASKET, METAL FLANGE AND SCREW(S) Mounting ring and 3 screws Snap ring / REMOVING YOUR OLD DISPOSER. FIRST, TURN OFF ELECTRICAL POWER at the service panel (fuse box or circuit breaker box). If the mounting is the same as your new disposer's mounting, you can use the existing mounting. Follow instructions A through E, Step 2, then go on to Step 10. Use a pipe wrench to disconnect the drain line where it attaches to the disposer discharge tube. Wire Nuts Now, use a screwdriver to remove ground wire. Remove the wire nuts from the power wires. Separate the disposer power wires from the cable wires. Loosen the screw(s) on the cable clamp and remove the cable from the disposer. If your old disposer has a different mounting than your new one, follow steps F and G. Otherwise go on to Step 3. i B. IF YOUR OLD DISPOSER HAS A DIFFERENT MOUNTING THAN YOUR NEW ONE, GO ON TO INSTRUCTION C. If your old disposer has the same mounting as your new one, insert the end of your "wrenchetta" or screwdriver into the right side of one of the disposer mounting ring lugs at the top of the disposer. Then, turn the "wrenchette" or screwdriver to the left (counterclockwise) until the lug lines up with one of the sink mounting assembly screws. CAUTION: Be sure to hold-the disposer with one hand while performing this step or it may fall when the mounting ring is disconnected from the sink mounting assembly. GO TO INSTRUCTION 13. Screw If your old disposer has a different mounting than your new one, use a pliers or adjustable wrench to remove the nuts on the mounting ring. Then remove old disposer. (Some disposers have to be removed by taking off a clamp or by twisting the disposer to remove it from its mounting. Easy to figure out.) Loosen screws and remove old mounting ring and back-up ring. You may need ahammer to loosen assembly parts. Once the disposer is off, turn it upside down and remove the electrical plate. Finally, remove the old sink sleeve by pushing it up through the sink hole. 3 CLEANING YOUR SINK'S DRAIN LINE. NOTE: In case of new construction, you may skip this step. The cutting elements on your old disposer were probably worn and not grinding the waste completely, Your drain line may be partially blocked. We recommend cleaning lhe line before connecting your new Kenmore disposer. Before routing You can do the job yourself with a drain auger, Remove the drain trap and, using the auger, clean out the horizontal drain pipe that runs from the trap to the main wasle pipe. Horizontal / Drain Pipe / Watch these trouble spots when routing Aflermufing with auger 4 4 HERE IS WHAT TO EXTENSION TUBE DO IF YOU ARE INSTALLING YOU R SINK'S FIRST DISPOSER, Use a pipe wrench to loosen the nut at the top of the drain trap. Now, remove the large nut at the base of the sink strainer by placing the Loosen the nut until you can spin it tipofyourscrewdriver on the edge of the nut. (There are usually ridges off by hand. to hold your screwdriver,) Then strike the head of the screwdriver with a hammer in a counterclockwise direction. SUPPLY. ELECTRICAL @ Before you begin this job, you should be thoroughly First, remove the fuse or turn off the circuit breaker on the circuit you plan familiar with electrical power and proper procedures. Local to use for your disposer. Use a electrical codes must be followed. If you are not sure, call separate 15 or 20 amp., 115 volt cir cuit for the disposer. in a professional who is knowledgeable. If you are replacing an old disposer, This appliance is equipped with copper wires. Use 3 con- skip to Step 6. ductor copper cable in accordance with your loc...