Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
CONTROLLER WARNING DISPLAYS.......................................................................................23 L20-294, rev. 0 (1/06) PG14D: Floor Model Gas Pasta Cooker INSTALLATION 1 Accessories # Description PG14D RS14D 1 Basket Hanger Standard Standard 2 Tube Rack Standard N/A 3 Drain Cleanout Rod Standard 4 Small Bulk Pasta Basket Optional Optional 5 Large Bulk Pasta Basket Optional Optional 6 Small Round Pasta Basket Optional Optional 7 Large Round Pasta Basket Optional Optional 8 Oblong Pasta Basket Optional Optional 9 Portion Cups with Rack Optional Optional 1. INSTALLATION 1.1. CHECKING YOUR NEW APPLIANCE Your new Pitco appliance has been carefully packed into one crate. Every effort has been made to ensure that it is delivered to you in perfect condition. As you unpack your new appliance, inspect each of the pieces for damage. If something is damaged, DO NOT sign the bill of lading. Contact the shipper immediately; the shipper is only responsible for 15 days after delivery. Check the packing list enclosed with your appliance to ensure that you have received all the parts to the appliance. If you are missing any parts, contact the dealer from whom the appliance was purchased. As you unpack the appliance and its accessories be careful to keep the weight of the appliance evenly distributed. Refer to the table below to identify which accessories should be included with your appliance. Locate your Pitco model number and serial number on the inner door of the appliance and the find the date purchased. Write this information on the front cover of this manual for future reference. If you have completed the above steps that are applicable to the appliance you purchased, the appliance is now ready to be installed. Although it may be possible for you to install and set up your new appliance, it is STRONGLY recommended that you have this done by qualified professionals. A qualified professional will ensure that the installation is safe and meets local building and fire codes. INSTALLATION WARNING DO NOT sit or stand on this appliance. The appliance’s front panel, tank, splash back, tank cover, workshelf, drain board is not a step. Serious injury could result from slipping, falling or contact with hot liquids. 1.2. INSTALLATION CLEARANCES The clearances shown below are for combustible and non-combustible installations and will allow for safe and proper operation of your appliance. Combustible Construction Non Combustible Construction Inches (centimeters) Inches (centimeters) Back Sides Counter 6.0" (15.24cm) 0.0" (0.0cm) 6.0" (15.24cm) 0.0" (0.0cm) 6.0" (15.24cm) 6.0" (15.24cm) In addition to the above clearances there must also be at least 16 inches (40.64cm) of aisle space in front of the unit. WARNING DO NOT obstruct the flow of ventilation, or air openings around the appliance. Adequate clearance around the appliance is necessary for servicing and proper component ventilation. Ensure that you meet the minimum clearance requirements specified in this manual. WARNING DO NOT install this appliance next to a deep fat fryer. A splash over of water into the hot oil may cause a flash fire. CAUTION To prevent equipment damage and/or personal injury, do not tilt the appliance onto any two of its casters or legs, or pull the appliance by the splash back. L20-294, rev. 0 (1/06) PG14D: Floor Model Gas Pasta Cooker INSTALLATION 3 1.3. LEG/CASTER INSTALLATION AND LEVELING When you receive your appliance it is completely assembled with the possible exception of the legs (or casters). This appliance must be installed with legs or casters; it cannot be curb mounted. Curb mounting will seriously inhibit this appliance’s ability to effect proper component ventilation. The legs/casters must be installed before connecting the appliance to the gas supply. The legs provide the necessary height to meet sanitation requirements and assure adequate air supply to the combustion system. Use the following procedure Required tools: 7/16 “ wrench and socket and a large pair of water pump pliers. 1. Lay the appliance on its back, being careful not to damage the splash back by pulling on it. Protect the outside of the appliance with cardboard or a drop cloth when laying it down. 2. Attach each leg/caster with the hex head screws and nuts supplied. Each leg/caster requires four .-20 x 5/8” hex head screws and nuts. Insure that all screws are tight. 3. Mount the screws from the inside of the appliance with the nut on the outside (bottom) of the appliance. The nuts have lock washers attached to them, therefore it is not necessary to use separate lock washers. 4. When all four legs/casters are securely mounted, stand the unit up, being careful not to put too much weight on any one leg. Adjust the height and level the appliance by adjusting the leveling devices (B) with water pump pliers. On casters, loosen 2 screws (A) before leveling, make your height adjustments, then retighten. WARNING DO NOT install legs or casters, or perform leveli...
Otros modelos de este manual:Otros aparatos de cocina - RS14D (1.56 mb)