Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
NOTE: Terminal block 120 Includes push-in locking terminals for internal wiring. Leads inserted in the front-most terminals may only be released by inserting & small screwdriver or similar in the slots provided in the front of the terminal block. Rear-most leads may release with a sharp pull. If leads cannot be released, or are not gripped on insertion, item 120 must be replaced. 2. Open the sliding tabletops and remove glass dishes and lids 101 and holders 103. 3. Remove the sliding tabletops as in A. 1. Then slide each tabletop in turn inwards past its closed position to gain access to the four screws securing top element assembly 107. 4. Use a powerful magnet or suitable tool to lift the element assembly out clear of the cabinet, feeding the element wires through grommet 110 in the cabinet. 5. Refit in reverse order, taking care that the rear cover strip fixing screw is clear of cables when fixing. 2 D. MIDDLE AND BOTTOM ELEMENT ASSEMBLY / NEON 1. Remove rear cover strip 510 as shown in C.1. And disconnect the middle shelf element leads 113 from terminal block 120 (See note in C. 1.) 2. Remove the two screws securing the element assembly through the rear panel of the cabinet, and two screws from under the front edge of the shelf (bottom element front screws are under the front of the cabinet,behifld the bottom. rail) — see fig.1. 3. Lift the element assembly out clear of the cabinet, feeding the element wires. through grommet 110 in the cabinet. 4. Neon 11 8 is a push fit assembly which is located by two barbs that spring open behind element panel trim 5.1.5. It can only be removed from the front. Pushing from behind the neon assembly (inside the front shelf rail) using a suitable tool can assist removal. To re-fit, thread the neon leads through the hole in the element panel trim 51 5, push-fit neon into hole and route with element leads to terminal block. 5. Re-fit in reverse order, taking care that the rear cover strip fixing screw is clear of cables when fixing. Fig. -HL6232E/F Element Assembly Fixing Points E. MAINS LEAD 1. Remove rear cover strip 510 as in C.l. 2. Disconnect LIVE and NEUTRAL mains lead wires from terminal block 1 20: release the earth lead from the cabinet earth stud. 3. To remove mains lead bush 121, rotate the retainer arm through 90., then use pliers to squeeze the mains lead locking tab and push the bush, complete with mains lead, out of the cover strip. 4. Refit in reverse order, ensuring correct wire colour connections and that a sound earth connection is made. 3 F. CABINET ITEMS 1. Magnetic catches 111 are a push-fit in front top panel 109. 2. To remove front top panel 109, remove both sliding tabletops completely (see A.1.) and magnetic catches 111. Drill out the rivet at each end of the front slide panel using a 3mm bit. Use extreme care when drilling Withdraw leg top caps 108, and then remove the front top panel assembly. Refit in reverse order. 3. Castor wheels 116 are a push-fit onto castor wheel inserts 117. The castor wheel inserts are a push-fit into the cabinet. Remove by prising out with care. THEORETICAL WIRING DIAGRAM SPECIFICATION Voltage 120 V ac. 60Hz Loading 410 W (Top 110 W, Middle 110 W, Bottom 190 W) Cord length 2 m Pre-heat time 30 minutes approx Finish See text Dimensions (approx) 725mm W x 380mm D x 695mm H SERVICE INFORMATION The elements used in this appliance are of the adhesive variety and cannot be removed easily. For this reason, elements and plates are supplied as complete assemblies. 4 5 SPARE PARTS LIST ITEM DESCRIPTION CODE 101 GLASS DISH & LID 0101 092 21701 103 GLASS DISH HOLDER 0101 081 00161 104 TABLE TOP COVER SEE ITEM 150 105 TABLE TOP HANDLE 0101 077 61391 106 TABLE TOP SLIDING BLOCK 0101 077 61341 107 TOP ELEMENT ASSEMBLY 0101 089 24271 108 LEG TOP CAP 0101 077 61311 109 FRONT TOP PANEL SEE ITEM 150 110 GROMMET SLEEVE 0101 078 53301 111 MAGNETIC CATCH (FS10) 0101 078 53351 112 MID ELEMENT ASSEMBLY 0101 089 24261 116 BRUANDET CASTER (4 PACK) 0101 078 53291 117 CASTOR INSERT 0101 077 61301 118 NEON ASSEMBLY 0101 078 53872 120 TERMINAL BLOCK 0101 078 53261 121 STRAIN RELEASE BUSH 0101 077 61511 122 MAINS CABLE 0101 076 53022 123 DOOR ASSEMBLY RIGHT SEE ITEM 150 124 DOOR HANDLE PAIR 0101 092 30061 125 DOOR ASSEMBLY LEFT SEE ITEM 150 126 DOOR HINGE PIN 0101 075 71811 127 BOTTOM ELEMENT ASSEMBLY 0101 089 24251 129 SCREW COVER CAP 0101 077 61381 130 SCREW COVER CAP 0101 077 61461 150 FULL WOOD SET 0101 092 30031 508 CABINET FRAME 0101 081 00311 512 PLINTH SEE ITEM 150 OUTERGLIDECOVER(PRINTED)010107771441 PLEASE NOTE FULL WOOD SETS INCLUDE DOORS, FRONT PANEL, PLINTH, AND TABLE TOPS 6 ...
Otros modelos de este manual:Otros aparatos de cocina - CM 3000 (489.71 kb)