Votos - 5, Puntuación media: 4.4 ( )

Fabricar: Cornelius Tamaño del archivo: 145.08 kb Nombre del archivo: Idioma del manual:

NOTE: Adjust the automatic agitation timer located in the dispenser’s electrical control box to 5 seconds on, 20 minutes off. Access to the timer is provided by removing the merchandiser/upper front panel. 1. Remove the top plastic bin covers (2) from the dispenser. 2. Place the ice maker adapter lid assembly (item 1) on top of the dispenser and position it flush with the rear and sides of the dispenser as shown in Figure 1. 3. Install the ice baffle on the lid assembly as shown in Figure 2. Release Date: November 10, 2010 Revision: F © 1998-2010, IMI Cornelius Inc. - 1 - Publication Number: 92254 ED300 Dispenser Kit Installation Instructions IMPORTANT: The baffle prevents ice from over-filling the manual fill area during agitation/ dispensing with a full storage bin and forcing the manual fill cover off. 4. Using the slotted holes in the lid as a template, drill (4) 0.147” diameter holes (#26 drill) at the bottom of the slots (see Figure 1 Detail A). BE CAREFULLY NOT TO DRILL INTO THE ICE STORAGE BIN. Secure the lid to the dispenser with (4) #10 sheet metal screws. 5. Seal the ice maker to the dispenser lid as follows (see Figure 1). A. Run beads of RTV around the opening in the lid and inside of the perimeter of the ice maker outline so that the ice maker will set on the RTV. B. Set the ice maker onto the lid and position it as shown in Figure 1. C. Wipe away the excess RTV. 6. Drill 0.147” diameter holes into the ice maker cabinet and the dispenser lid using the ice maker mounting brackets as templates. USE CAUTION SO AS NOT TO DRILL INTO ANY ICE MAKER COMPONENTS (CONDENSER, TUBING, ETC.). Secure the brackets using the #10 sheet metal screws provided. 7. Follow the ice maker manufacturer’s instructions to complete the installation of the ice maker including the bin thermostat if so equipped or required. IMPORTANT: For Scotsman CM series ice makers with sonic ice level control, Bin Thermostat Kit KSB1 must be ordered with the ice maker ! CAUTION: The bin thermostat location must not interfere with agitator rotation. 8. Locate the cleaning caution label (item 5) on the manual ice fill cover (item 4) as shown in Figure 1. Place the manual fill cover in position over the flange on the lid assembly and the front access hopper opening. Figure 1. Dispenser 30 7 3 SEE DETAIL A 7 ICEMAKER SEAL TO ITEM 1 WITH ITEM 3 REFER TO STEP 5 DETAIL A DRILL o .147 HOLES USING BOTTOM OF SLOTTED HOLES IN LID AS A TEMPLATE 5 4 2 1 POSITION ICEMAKER FLUSH WITH REAR OF LID AND CENTERED ON DISPENSER 7. Publication Number: 92254 - 2 -© 1998-2010, IMI Cornelius Inc. ED300 Dispenser Kit Installation Instructions © 1998-2010, IMI Cornelius Inc. - 3 - Publication Number: 92254 Figure 2. ED300 Baffle Kit Figure 3. Mounting Template 4 PLC. ICEMAKER SHOWN FOR REFERENCE ONLY 4 PLC. BAFFLE (ITEM 6) SHOWN IN PLACE 4 PLC. 1 9 8 6 10 o 7/16 (6) PLCS OPENING 18 5/8 8 5/8 22 3/8 3 3/16 44 3/8 29 3/4 31 1/2 15 3 1/2 20 3/8 1 13/16 40 3/4 1 5/16 6 11/16 21 1/4 15 12 4 ...

Descargar ahora

Introduzca dos números de la imagen: