Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
Dimensions and clearances A – 34" (864 mm) adjustable to 35" (889 mm) B – 12" (305 mm) C – 20-1/4" (514 mm) D – 22" (559 mm) E – 2-3/4" to 4-1/4" (70 mm to 108 mm) base is adjustable from front panel Note: If cord is to be plugged in directly behind compactor add 2-1/2" to overall depth in order to allow proper clearance for the electrical cord. Installation Preparation Built-In Compactors Standard Appearance Panel Options The Monogram compactor models ZCG3300 and ZCG3100 come with a white/black reversible aluminum front drawer panel. Model ZCG3300 is shipped with the white panel showing and model ZCG3100 with the black side showing. The panels on both models can be reversed to reveal the opposite color side. The ZCG3500 comes with a stainless steel wrapped panel. Go to Step 7, page 12. Follow procedure A for reversing door panel color if desired. Custom Monogram compactor models ZCG3300 and ZCG3100 You can: Panels are designed to accept a custom front drawer panel to • Install a 1/4" thick custom panel match the surrounding cabinetry. • 3/4" thick custom panel • 3/4" thick custom panel and custom handle Option #1 1/4" Thick Wood Panel • Cut panel 11-11/16" wide, 24-1/2" high. The custom 1/4" thick panel replaces the white/black aluminum panels and cardboard filler. The custom panel will slide into the trim on the drawer front, concealing raw cut edges. Option #2 Go to Step 7, page 12. Follow procedure B for installation. 3/4" Thick Wood Panel • Cut panel 12" wide x 24-3/4" high. The custom 3/4" thick panel replaces the white/black aluminum panel. Cut edges will be seen and must be finished for best appearance. Both the trim and drawer front panel will be removed to make this installation. Go to Step 7, page 12. Follow procedure C for installation. Note: 3/4" thick door panels, both raised and flat design, should be constructed in the same manner as typical cabinet doors. Order the 3/4" custom door panel from the cabinet manufacturer. Be sure to provide the exact dimensions so that the panel is constructed accurately. Pour votre securite personnelle, n’utilisez pas de rallonge ou de fiche d’adaptation avec cet appareil. Ne coupez ou n’enlevez pas, pour quelque motif que ce soit, la troisieme broche de masse du cordon d’alimentation. Pour votre securite personnelle, n’utilisez pas de rallonge ou de fiche d’adaptation avec cet appareil. Ne coupez ou n’enlevez pas, pour quelque motif que ce soit, la troisieme broche de masse du cordon d’alimentation. Installation Preparation Built-In Compactors Option #3 Power supply 3/4" Thick Wood Panel with custom handle • Cut panel 12" wide x 25-13/16" high. A custom handle, of your choice, can be installed onto the 3/4" wood panel, replacing the standard handle. The cut edges of the custom panel can be seen and must be finished for best appearance. The trim, drawer front panel and the handle will be removed to make this installation. Go to Step 7, page 14. Follow procedure D for installation. Note: 3/4" thick door panels, both raised and flat design, should be constructed in the same manner as typical cabinet doors. Order the 3/4" custom door panel from the cabinet manufacturer. Be sure to provide the exact dimensions so that the panel is constructed accurately. Order custom handle to match cabinetry hardware. CAUTION For personal safety, do not use an extension cord or adapter plug with this appliance. Do not, under any circumstances, cut or remove the third grounding prong from the power cord. MISE EN GARDE Follow national electrical codes or prevailing local codes and ordinances. This appliance must be supplied with 120V, 60HZ and connected to an individual, properly grounded branch circuit protected by a 15 or 20 amp circuit breaker or time delay fuse. Install a 3-prong grounding type receptacle in the rear wall of the cabinet opening. 25-13/16" 12" 3/4" Note: The outlet location is critical for proper cord storage when compactor is installed. Note: Usable power cord length is 3 to 4 ft. Installation Built-In Compactors Tools required: •#2 Phillips head screwdriver • Flat blade screwdriver •Tape measure •Spirit level •10" long 2x4 •Adjustable wrench or slip joint pliers •Drill and 1/8" drill bit Parts List: •4 leveling feet caps •4 Phillips head screws • 2 Slotted head screws •2 Tip-over brackets •2 90° clips Optional Materials (not supplied): •Custom front panel • Custom handle •Custom toekick board •5 wood screws Technical Electric Power—120V, 60 HZ, 5 amp Container volume—1.4 cu. ft. data Circuit Requirement—15 or 20 amp grounded outlet Weight—135 lbs. Motor Horsepower—1/3 Cycle Time—70 sec. max., 12 sec. min. Compacting Force—5000# max. Choosing This compactor is designed as a built-in appliance the only. It may be located in any convenient space under location a countertop. DO NOT OPERATE FREE-STANDING because the compactor will tip over when the drawer is pulled out. Installation Built-In Compactors Installation If compactor is to be located in or near a corner ...
Otros modelos de este manual:Otros aparatos de cocina - MONOGRAM ZCG3300 (286.92 kb)
Otros aparatos de cocina - MONOGRAM ZCG3100 (286.92 kb)