Votos - 2, Puntuación media: 3.5 ( )

Fabricar: Follett Tamaño del archivo: 1.97 mb Nombre del archivo: Idioma del manual:

1. Replace upper (power) strain relief with a cord connector. 2. Mount two 51mm x 102mm (2" x 4") junction boxes using supplied holes in icemaker face. 3. Make power and bin signal connections. Dispenser Lower icemaker Upper icemaker LEGEND junction box junction box (bin signal) junction box (power) WIRENUT FIELD CONNECTIONS EQUIPMENT GROUND B BLACK W WHITE GRN GREEN BL BLUE Y YELLOW RD RED VU155/VU300 ice and beverage dispenser with either ONE or TWO autofill icemaker kits X GND GRNWB WR B Electric power source 25, 50 or 110 ice and water dispenser with ONE Satellite-fill icemaker X WGNDGRNB Electric power source X Icemaker #1 (optional) DISPENSER Left junction box GND GRNB WRight junction box BL Y RD WB Lower junction box (24Vbin signal) Icemaker #2 (optional) WB XGND GRNB WLower junction box (24Vbin signal) Upper junction box (power) XGND GRNB WUpper junction box (power) Electric power source Electric power source Electric power source 10 Install icemaker and rough-in utilities with optional slide-out accessory The slide-out accessory allows the icemaker to be pulled out on a track from below a counter without disconnecting utilities. A leg supports the icemaker in the full-out position. If your order did not include a slide-out accessory proceed to icemaker ventilation and exhaust. Step 1 – Installing track accessory (Follow either A or B below) Track must be positioned flush against inside of counter and slightly above counter access opening. A. When icemaker stand is used (required if icemaker is not supported on counter channels) 1. Bolt vertical utility panel to slide-out track assembly with supplied 10/32 screws. 2. Secure slide-out track assembly to icemaker stand with 10/32 screws provided. 3. Position icemaker stand in desired location and adjust stand legs to proper height and level in both directions. 4. Using holes in flanged legs as template, mark floor for 12 anchoring holes to be drilled. 5. Remove stand/track assembly and drill marked holes. 6. Reposition and anchor stand to floor with 12 fasteners appropriate to floor material (not supplied). Stand MUST be anchored to avoid tipping and possible injury when icemaker is pulled out. B. When icemaker is supported on counter channels 1. Bolt vertical utility panel to slide-out track assembly with supplied 10/32 screws. 2. Position track assembly on counter channels (Fig. 3). 3. Using holes in track assembly as a template, mark and drill required holes in counter channels. 4. Remove track assembly on channels and drill marked holes. 5. Reposition track assembly on channels and secure using appropriate hardware (not supplied). verical utility panel331mm (13") 356mm (14") 324mm (12.75)356mm (14") bin signal water in slide-out-track icemaker drain 11 Step 2 – Installing icemaker on slide-out track A. When icemaker is shipped with slide-out track accessory (follow either A or B) 1. Connect inlet water, drain, and power supply to back of vertical utility panel. 2. Place icemaker on slide-out track assembly. 3. Connect drain and water lines. 4. Connect electrical cords from icemaker to appropriate plug and connect to power supply. B. When icemaker is installed in and shipped with counter 1. Remove two outer rear screws from icemaker and install supplied spacer and screw (Fig. 3). 2. Place icemaker on slide-out track assembly. 3. Connect drain and water lines. 4. Connect electrical cords from icemaker to appropriate plug and connect to power supply. 5. Remove pin from adjustable leg. 6. Place hold-down strap over leg block and secure strap to slide-out assembly with supplied screws (Fig. 4). 7. Reinstall pin in leg block. 8. At job site remove hold-down strap and make utility connections at rear utility panel. position track accessory so that 51mm (2") duct supplied with air- cooled remote icemaker mates with back of counter opening counter front grille supplied with air-cooled Satellite-fill icemakers air in (air-cooled units only) utility connections made at back side of panel (see next page) Fig. 3 Fig. 4 Remove screw. Install supplied screws and spacers. hold-down strap (for installation; remove and discard) supplied screws (for installation; remove and discard) 12 Front view Side view (All customer field connections are made to rear of vertical utility panel) 658mm (25.875") 3/8" OD push-in condenser drain (water-cooled only) 3/8" OD push-in icemaker water inlet barbed push-on icemaker drain vertical utility panel 3/8" OD push-in condenser inlet (water-cooled only) 3/8" OD push-in condenser drain (water-cooled only) 3/8" OD push-in icemaker water inlet bin signal cord connector (to connect to dispenser bin signal cord) 578mm (22.75") 3/4" MPT icemaker drain cord holder Plan view 13 Satellite-fill icemaker ventilation and exhaust requirements Fabricator-supplied, custom air intake grilles must have 305mm x 305mm (12" x 12") opening yielding 645 sq. cm (100 sq. inches) of open air space within duct perimeter. Block off any open area outside of the...

Descargar ahora

Introduzca dos números de la imagen: