Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
4. Replace the cutter grid cover with the 3 screws. 5. Plug in the icemaker or reconnect power. Vacation To shut down the icemaker: and moving 1. Unplug the icemaker or disconnect power. 2. Remove all ice from the storage bin. 3. Shut off the water supply. 4. Remove the 2 screws in the lower access panel and the 2 screws from the base grille area of the front panel support. Pull forward to remove the lower access panel. 5. Disconnect the inlet and outlet lines to water valve. Allow these lines to drain and then reconnect to the valve. 6. Replace the lower access panel and screws. Drain water from water pan by removing the drain cap. Also, remove water from drain line. 7. Before using again, clean the icemaker and storage bin. 8. Plug in the icemaker or reconnect power. NOTE: All components of the icemaker are permanently lubricated at the factory. They should not require any additional oiling throughout the normal life of the machine. Preparation Icemaker Front leveling legs Your icemaker has 2 adjustable leveling legs to help you steady the product and make sure it is level. 1. Place a carpenter’s level on top of the icemaker to make sure it is level from front to back and side to side. 2. Lift the top front of the icemaker to locate the leveling screws that are on the bottom front. 3. Using an adjustable wrench, change the height of the legs as follows: •Turn the leveling leg to the right to lower that side of the icemaker. •Turn the leveling leg to the left to raise that side of the icemaker. NOTE: The icemaker should not wobble. Use shims to add stability when needed. Raise Lower 4. Use a carpenter’s level to make sure the icemaker is even from front to back and side to side. Reversing the Door Swing Icemaker To reverse the door TOOLS NEEDED: 5.16. wrench, 1.4. wrench, flat putty knife, Phillips screwdriver Parts Supplied: Four plug buttons Parts Identification: (For Reference Only) Hinge Pin Handle Screw 5/16. Hex Head Endcap Screw Hinge Screw IMPORTANT: Before you begin, unplug the icemaker or disconnect power. To remove door from hinges: 1. Remove the handle screws and lift off the handle (on some models). Keep the parts together and set them aside. 2. Remove the hinge pin from the top hinge. 3. Lift the door off of the bottom hinge. Place the hinge pin back into the top hinge. 4. Reverse the door endcaps as follows: •Remove the screws and endcaps from the door, top and bottom. •Place the top endcap on the bottom of the opposite side of the door with the long flat side facing the door front. •Place the bottom endcap on the top of the opposite side of the door with the long flat side facing the door front. 5. Set the door aside. Top Hinge To reverse the hinges: 1. Using a flat putty knife, remove the plug buttons from the screw holes opposite of the door hinges, top and bottom. Set aside. 2. Remove the two screws holding the top hinge. Turn the hinge upside down so that the hinge pin points up. Place the hinge on the opposite side at the bottom of the door. 3. Remove the plastic hinge sleeve from the “old” bottom hinge and replace it on the new bottom hinge pin. 4. Remove the bottom hinge. Turn the hinge upside down so that the hinge pin points down. Place the hinge on the opposite side at the top of the door. 5. Push the plug buttons into the original screw holes. 6. Remove the top hinge pin. Top Hinge Bottom Hinge Bottom Hinge Hinge Pin Hinge Sleeve/ Door Stop Hinge Plugs Hex Head Hinge Screw Hinge Sleeve/ Door Stop Plugs Hinge PinHinge Hex Head Hinge Screw Reversing the Door Swing Icemaker To reverse the door To replace door on hinges: 1. Place plastic hinge sleeve on bottom hinge and position the door on the pin. 2. Place plastic hinge sleeve in the top hinge hole on the door. Align the door on the bottom hinge and replace the top hinge pin. 3. Replace the handle and handle screws. To reverse the door catch: 1. Remove the plugs buttons from the opposite side of the door. 2. Remove the screws from the magnetic door catch and replace it on the opposite side of the door. 3. Push the plug buttons into place on the opposite side of the door. Reverse Door Catch Position The Problem Solver Icemaker PROBLEM POSSIBLE CAUSE Questions? Use this problem solver! ICEMAKER DOES NOT OPERATE • Power cord is not plugged into a live outlet. • The control is set at OFF. • The fuse is blown/circuit breaker is tripped. Replace fuse or reset the breaker. • Room temperature is colder than normal. Room temperature must be above 55°F (13°C). Otherwise, bin thermostat may sense cold room temperature and shut off even though the bin is not full of ice. Also, unit may not restart once it does shut off. ICE CUBES HAVE • High mineral content in the water supply. Water may need to ODOR/TASTE be filtered or treated. • Food items stored in ice bin. Do not store any foods in the ice bin. • Packaging materials were not removed. Make sure that all packaging materials were removed at the time of installation. • Ice storage bin needs c...
Otros modelos de este manual:Otros aparatos de cocina - ZDIS15 (329.53 kb)