Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
Things to Remember • Allow your ice machine to run for 24-48 hours to accumulate ice in ice machine's bin. • Unit will cycle often between ice production and ice harvest cycles. • Your unit will automatically shut down when the ice bin is full. • Unplug your ice machine before working on unit. • Keep your ice machine clean for proper ice quality, production, and unit life. • Room and water temperatures will greatly affect the output of ice in your unit (see table). Ice will also melt away, especially at the start of an empty bin, but will slow down as ice accumulates. Obtaining Service Before Calling for Service Before calling for service, check the following items: • Make sure unit is plugged into outlet. • Check the outlet for power. Test outlet with lamp to make certain outlet has power. • Make sure ice machine's switch is in the "ON" position. • Make sure that there is cold water supplied to the ice machine. • Make sure drain plug on bottom of reservoir is inserted. • Make certain unit is level from front to back and side to side. • Make certain that the drain line to the ice machine is unrestricted or kinked. • Use troubleshooting guide, pages 11-14 for other diagnosis. If you are not able to correct the problem, contact your dealer or the manufacturer. Be sure to have the model number and the serial number handy before you call. The model and the serial number are located on the lower front part of the ice machine's cabinet. How to Obtain Service Your ice machine requires little service because the best and most up-to-date materials, equipment and quality control methods are employed throughout the manufacturing process. If trouble occurs during normal operation, read "Things to remember" section first and, if necessary, check the troubleshooting guide. If service becomes necessary: 1. Contact the dealer where your appliance was purchased or the manufacturer for the name of the nearest authorized service representative. The service representative will have full authority to make any repairs deemed necessary. 2. If you are in an area where there is no service representative, write or call the manufacturer directly. We will make recommendations as to the proper procedure for correction. Service work and replacement parts, if required, will be provided as covered by your limited warranty. 3. In all correspondence regarding service, be sure to give the model number, serial number and proof of purchase. 4. Try to have information or description of the nature of the problem, how long the unit has been running, the room temperature, water temperatures, and any additional information that may be helpful in quickly solving the problem. Every new ice machine that leaves the factory contains this Owner's Guide. Keep this Owner's Guide in a safe place for convenient reference. SEND IN YOUR WARRANTY RECORD CARD IMMEDIATELY AFTER TAKING DELIVERY OF YOUR ICE MACHINE. For Your Records Date of Purchase Dealer's Name Dealer's Address Dealer's city Dealer's State Zip Appliance Serial Number Model Number Date Warranty Card Mailed (within 10 days of purchase) All specifications and product design subject to change without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions, replacements or compensation for previously purchased products. Troubleshooting One Problem Possible Cause Correction Unit does not operate. The unit is unplugged. Plug in the unit. Breaker is tripped or fuse is blown. Reset breaker or replace fuse. Check to make sure there is not a short in the electrical circuit. Ice machine selector switch is in the "OFF" position. Set the rocker switch on the grille of the ice machine to the "ON" position. Unit operates but does not produce any ice. The unit has just been started and it has been less Ice produced when the unit is initially started will melt off in the bin. Ice than 6 hours. will accumulate in the bin. In 6 hours there can be a few cubes in the bin. This is normal operation. Typical ice production cycle can take up to 1.5 Check the unit in 24 hours for ice accumulation in the bin. hours. Initial startup cycles can be longer. The selector switch is in the "OFF" or "CLEAN" Set the rocker switch on the grille of the ice machine to the "ON" posiposition. tion. No water in the reservoir. Make sure that the reservoir drain plug is installed. Check the water line to the unit to make sure it is on and that there are no restrictions or kinks in the line. Check all filters to make sure they are not restricted or plugged. Distributor tube is restricted. See "CLEANING YOUR ICE MACHINE" section for cleaning the unit for proper operation. Build up of deposits on evaporator plate. See "CLEANING YOUR ICE MACHINE" section for cleaning the unit for proper operation. Condenser fan air flow is restricted. Make certain the grille in the front of the unit is free and open for proper air circulation. Check and clean the condenser coil by removing the grille in the front of the...