Votos - 2, Puntuación media: 5
(
)
)
|
Resumen del manual
Important Save the carton packaging until your ice machine has been thoroughly inspected and found to be in good condition. If there is damage, the packaging will be needed as proof of damage sustained in transit. Note to Customer This ice machine was carefully packed and thoroughly inspected before leaving our plant. Responsibility for its safe delivery was assumed by the carrier upon acceptance of the shipment. As directed on the side of the packaging carton, claims for loss or damage sustained in transit must be made on the carrier as follows: Exterior Damage Make a thorough damage notation on the delivery receipt and have the driver acknowledge by signing and dating. Send a written request to the carrier asking for an inspection report from the carrier representative and the date the inspection was requested. Retain the inspection report and receipt for filing of a claim. Concealed Damage This must be reported to the carrier within fifteen days. Obtain an inspection report from the carrier. Retain the inspection report for filing of the claim. DO NOT RETURN DAMAGED MERCHANDISE TO THE MANUFACTURER - FILE THE CLAIM WITH THE CARRIER. INSTALLATION: DRAIN PLUMBING figure 1 figure 2 Drain Plumbing Your ice machine uses a gravity drain, (figure 1) that requires 5/8" I.D. tubing from the back of the ice machine to a plumbed connection to a sanitary sewer. Remove the access panel to plumb in drain connection. Gravity drain location for built-in units can be within the area shown in figure 3. An optional drain pump, (figure 2) can be purchased for your ice machine if a gravity drain is not accessible. OBSERVE AND FOLLOW ALL LOCAL CODES WHEN INSTALLING ICE MACHINE. FAILURE TO USE ADEQUATE DRAINAGE SYSTEM WILL RESULT IN SURROUNDING WATER DAMAGE AND/OR POOR ICE PRODUCTION. figure 3 Gravity Drain Location * With optional filler kit WATER SUPPLY Water Supply This ice machine must be connected to a potable, active cold water supply line delivering water pressure at a minimum of 20 psi and maximum of 120 psi. • Water connection is made through a right angle garden hose fitting supplied with ice machine. See garden hose fitting for detailed instruction sheet. Do not use any thread sealers. • A water filter can be used with this unit. A quality filter can help remove particles as well as remove taste and odors from water. • Do not use a “reverse osmosis” filtering device. • Softened water is not recommended. This will produce soft, cloudy ice cubes that will stick together. • De-ionized water is not recommended. This water will not form solid ice cubes. • A water specialist can recommend proper water treatment. • After installation of water line, turn on water and check for any leaks. Additional tightening may be needed. • Allow for extra water line for built-in installations for easy removal of unit and to help prevent the water line from kinking. Operation Your ice machine is unique in forming ice. It uses fractional freezing to form a slab of ice that is clear and has less mineral content than the water it is produced from. This is accomplished by running water over the cold evaporator plate which gradually freezes the water to produce the ice slab. Mineral deposits are left in the reservoir. When the ice slab reaches the correct thickness determined by the temperature of the evaporator plate, the electronic control switches to the harvest cycle to harvest the ice. During the harvest cycle, the ice slab falls from the evaporator to the ice grid cutter. Here, the ice slab is cut into 3/4" squares by the grid cutter's heated wires. During the harvest cycle, the drain valve will remain open for 45 seconds to drain the reservoir of remaining deposits. After that, the water valve open will open for 2 minutes providing 2 quarts of water to the reservoir for the next ice production cycle. The ice machine will keep producing ice until the ice machine's bin is full and will restart automatically when ice needs to be replenished in the bin. CARE OF THE UNIT Care of Unit 1. Avoid leaning on the cabinet door. You may bend the door hinge or tip the unit. 2. Exercise caution when sweeping, vacuuming, or mopping near the front of the unit. Damage to the grille and/or switch can occur. 3. Periodically clean the inside of the ice machine components and inside of unit (see Cleaning Your Ice Machine section). 4. Periodically check and/or clean the front grille and condenser coils as needed. 5. If your ice machine has either a stainless steel door and/or cabinet, to keep it looking its best, we recommend periodically applying a stainless steel cleaner and a non-abrasive stainless steel polish. This is especially important for outdoor applications and locations near saltwater environments. Normal Responsibilities of the Owner • All freight charges • Damage sustained in transit • Mileage charge(s) for service calls • Proper installation including installation of leveling legs. • Leveling of unit. • Alterations to original equipment • Remova...