Votos - 1, Puntuación media: 3
(
)
)
|
Resumen del manual
to a maximum comfortable working height of 291/4" above the floor. The Model H6240 was carefully packed when it left our warehouse. If you discover this hydraulic table cart is damaged after you have signed for delivery, please immediately call Customer Service at (570) 546-9663 for advice. Save the containers and all packing materials for possible inspection by the carrier or its agent. Otherwise, filing a freight claim can be difficult. When you are completely satisfied with the condition of your shipment, you should inventory the contents. Figure 2 - Inventory. A. Cart (Not Shown).......................................1 B. Handle........................................................1 C. Foot Pedal..................................................1 D. Hex Bolts M8-1.25 x 40..............................2 E. Hex Bolts M8-1.25 x 20..............................1 ▲WARNING This table cart is not a toy. DO NOT allow children to use this cart. Serious injury may occur if this cart is used incorrectly. Figure 1. 600 lb. Capacity hydraulic table cart. Figure 2. Inventory. ASSEMBLY OPERATIONS 1. Slide the lifting pedal into the pedal shaft, and insert the M8-1.25 x 20 hex bolt through the hole in the side of the pedal shaft and into the lifting pedal (Figure 3). 2. Place the handle in the handle sockets and secure with the M8-1.25 x 40 hex bolts (Figure 3). Figure 3. Assembly. Awarning Failure to follow these instructions will result in serious personal injury: 1. Keep hands out of the scissor lift to prevent serious pinching and crushing injuries. 2. DO NOT exceed the 600 lb. load capacity. 3. Lock the rear casters when loading and unloading the cart. 4. Balance the load evenly in the center of the cart. 5. Transport the load in the fully lowered position to prevent tipping. Awarning Keep hands out of the scissor lift to prevent serious crushing injuries. 1. Balance the load evenly in the center of the cart. 2. Pump the lifting pedal to raise the table. 3. Push the pressure release pedal to lower the table. Note—Always lower the table when not in use. MAINTENANCE 1. Fully lower the tabletop when not in use. 2. Wipe all dirt and dust off the table cart. 3. Apply light oil to the surface of the hydraulic jack ram. 4. Remove the plug on the top of the hydraulic jack to check the oil level. Add oil if necessary, replace the plug, then pump the handle several times with the pressure release valve open to bleed the air out of the system. If you need additional help with this procedure, call our service department at: (570) 546-9663. REF PART # DESCRIPTION REF PART # DESCRIPTION 18 PH6240018 SWIVEL CASTER 19 PLW04M LOCK WASHER 8MM 20 PN03M HEX NUT M8-1.25 21 PB15M HEX BOLT M8-1.25 X 40 22 PH6240022 PIVOT PIN 23 PH6240023 CONNECTING PLATE 24 PH6240024 PIVOT PIN 25 PH6240025 PEDAL SHAFT 26 PH6240026 COTTER PIN 27 PB26M HEX BOLT M8-1.25 X 30 28 PW01M FLAT WASHER 8MM 29 PH6240029 LIFTING PEDAL 30 PH6240030 HANDLE 31 PH6240031 PIVOT PIN 32 PR09M EXT RETAIN RING 20MM 33 PH6240033 DOWN PEDAL 1 PH6240001 TABLETOP 2 PH6240002 PIVOT PIN 3 PR06M EXT RETAIN RING 16MM 4 PH6240004 SCISSOR LIFT 6 PH6240006 WHEEL 7 PH6240007 BASE 8 PH6240008 PIVOT PIN 9 PH6240009 HYDRAULIC JACK 10 PB23M HEX BOLT M10-1.5 X 100 11 PH6240011 BUSHING 12 PH6240012 FRONT WHEEL 13 PW04M FLAT WASHER 10MM 14 PN02M HEX NUT M10-1.5 15 PH6240015 SPRING 16 PH6240016 SPRING CAP 17 PB09M HEX BOLT M8-1.25 X 20 COPYRIGHT © AUGUST, 2004 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. #EW6463 PRINTED IN CHINA...