Votos - 4, Puntuación media: 3.5
(
)
)
|
Resumen del manual
Important: Both LTO-2 and LTO-3 tape drives require Ultra 160 rated SCSI cabling, and an Ultra 3 or LVD 160 Active SCSI terminator. The StorageLoader 2U LTO ships from the factory with these accessories. ** To prepare your own labels, refer to the Tandberg Data Bar Code Label Specification for LTO Cartridges available at: Additional Items — You must have -or- obtain some or all the following items to complete the installation Host computer with adapter card installed You need a host computer with a host bus adapter card installed. Refer to the documentation that came with the computer and LVD SCSI or Fibre Channel (FC) adapter card. The StorageLoader 2U LTO is configured for LVD SCSI or Fibre Channel. Important: Both LTO-2 and LTO-3 tape drives are Ultra 160 SCSI devices and require a minimum Ultra 160 non-RAID SCSI host bus adapter card (LVD SCSI configuration only). Hybrid cable If your SCSI controller has a 68-pin VHDCI connector, you will need to obtain a VHDCI-to-HD SCSI cable. Tools You will need a #1 Phillips screwdriver. Fibre Channel cable If you have a Fibre Channel adapter card installed, you need to obtain a FC cable. Power cord (for use outside Europe) If you plan to use the library outside Europe, you must supply your own power cord (see the Product Manual at for information about an International 220 VAC power cord). Backup software You need a backup software application to manage your backup operations. Refer to the documentation that came with the backup software and make sure it supports the library. See for compatibility information. Data and Cleaning cartridges (available from Tandberg Data or your supplier) HD Connector VHDCI Connector Tape Ultrium 3 (slate blue) Ultrium 2 (purple) Ultrium 1 (black) LTO Ultrium Drive Read Write Read Write Read Write Cleaning Cartridge LTO-3 Yes Yes Yes Yes Yes No Yes LTO-2 No No Yes Yes Yes Yes Yes WARNING! The library weighs 44 lbs (20 kg). Two people are needed to move or lift the library. Most of the weight is toward the back of the library. WARNUNG! Die Library wiegt 20 kg. Es sind mindestens 2 Personen erforderlich, um die Library zu bewegen oder zu heben. Der hintere Teil der Library hat das Gro.te Gewicht. .PRECAUCION! La biblioteca montada sobre bastidor pesa 20 kg. Se necesitan dos personas para mover o levantar la biblioteca. La parte trasera de la biblioteca es la de mayor peso. Page 1 of 8 StorageLoader 2U LTO Quick Start Guide Step 1 — Before you begin 1 — Ensure that you have all the required items before you proceed (see Accessories and Additional Items on page 1). 2 — Locate an appropriate area for the unit that has adequate clearance for ventilation, minimal dust and debris, and an appropriate power source. The unit is designed for installation in a standard 4 post, 19-inch rack. 3 — Ensure that the work area is free from conditions that could cause electrostatic discharge (ESD). Discharge static electricity from your body by touching a known grounded surface, such as a computer’s metal chassis. 4 — The unit must be operated in the horizontal position. Do not place it on its side, and do not place objects on top of it. Step 2 — Unpacking 1 — Remove foam and accessories: LVD SCSI cable and terminator* Barcode labels and warranty Ethernet cable Power cables Rack mount kit 2 — Lift unit only by the 2 sides •LVD SCSI configuration only Important: Save all original packing materials in case you need to ship or move the library later. Step 2a — Rack-mounting (optional) If you plan to install the library in a rack, see the Rack-mount Instructions (complete prior to Step 3). WARNING! Before performing any installation or maintenance procedures, be sure that the library power switch is in the off position and that the power cord is disconnected from the library and the outlet. WARNUNG! Vor der Ausfuhrung von Installations- oder Wartungsarbeiten ist darauf zu achten, da. der Library-Netzschalter auf “Aus” gestellt ist und da. das Anschlu.kabel vom Library und der Steckdose entfernt ist. .PRECAUCION! Antes de realizar cualquier procedimiento de instalacion o de mantenimiento, comprobar que el interruptor de alimentacion de la biblioteca esta apagado y que el cable de alimentacion no esta enchufado ni a la biblioteca ni a la toma de corriente. Step 3 — Connecting the cables Fibre Channel connections: 1 — Connect Fibre Channel cable 2 — Connect Power cord SCSI connections (LVD only): 1 — Connect SCSI cable and Terminator* 2 — Connect Power cord S T FC E E P P T S FC P E Power switch (Off=0 On=I ) Ethernet port (see Product Manual for addressing; the default setting is DHCP enabled) Important: Both LTO-2 and LTO-3 tape drives require Ultra 160 rated SCSI cabling, and an Ultra 3 or LVD 160 Active SCSI terminator to function properly on the SCSI bus. An inadequate terminator will result in various SCSI bus issues, including bus hangs and Read/Write failures. See the “Troubleshooting” chapt...