Votos - 0, Puntuación media: 4
(
)
)
|
Resumen del manual
Keep the power cord away from heat, oil, sharp edges, or moving parts. replace damaged power cords immediately. Damaged Power Cords increase the risk of electric shock. 5. Always wear eye protection. Always wear ANSI-approved safety goggles when performing maintenance on this product. 6. do not use the product for a purpose for which it is not intended. 7. do not use the product if the power switch does not turn it on or off. Any product that cannot be controlled with the Power Switch is dangerous and must be replaced. 8. disconnect the power cord plug from the power source before making any adjustments, changing accessories, or storing the product. Such preventive safety measures reduce the risk of starting the product accidentally. Always unplug the product from its electrical outlet before performing any inspection, maintenance, or cleaning procedures. 9. store lantern out of reach of small children. 10. check for breakage of parts and any other condition that may affect the product’s operation. if damaged, have the product serviced before using. Many accidents are caused by poorly maintained products. 11. use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one product may become hazardous when used on another product. 12. product service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury. 13. when servicing a product, use only identical replacement parts. follow instructions in the “Inspection, Maintenance, And Cleaning” section of this manual. Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electric shock or injury. 14. maintain labels and nameplates on the product. These carry important information. If unreadable or missing, contact Harbor Freight Products for a replacement. 15. never leave the product unattended when its adapter is plugged into an electrical outlet. Turn off the product, and unplug the adapter from its electrical outlet before leaving. 16. use only rechargeable batteries when replacing the batteries. Do not substitute with any other size or type of battery. 17. never mix new and old batteries or batteries of different types together. Mixing batteries may result in fire, leakage, or explosion. SKU 94740 for technical questions, please call 1-800-444-3353. Page 3 18. nicd batteries must be disposed of or recycled properly. Do not incinerate. Batteries may burst, causing personal injury and/or property damage. Contact your local hazardous waste disposal authority for disposal or recycling. unpAcKing When unpacking, check to make sure that the product is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. note: The AC Adapter is located inside of the Bottom Cover. See instructions for removing the AC Adapter on page 6. operAting instructions note: For additional information regarding the parts listed in the following pages, refer to the Assembly diagram at the end of the manual. 1. Turn the switch to the “OFF” position – the unit will charge much faster if it is switched off while charging. Charge the batteries by using the wall adapter, car adapter, or sitting the Solar Lantern in the sunlight for an extended period. if using the automobile outlet, be aware that it will use up power and can drain the car battery. 2. Once the lantern is charged, turn the switch to the “ON” position to illuminate the lantern. Turn the switch to off to conserve power when done. 3. If the Solar Lantern stops working or is not holding a charge, replace the batteries - see next page. SKU 94740 for technical questions, please call 1-800-444-3353. Page 4 bAttery replAcement 1. Turn the Solar Housing Lid (7) slightly counterclockwise. Remove the Solar Housing Lid (7) from the top of the Solar Lantern. See Figure 1. 2. Remove the three Screws from the Battery Cover (6). See Figure 2. Solar Housing (7) Battery Cover (6) Figure 2 Batteries (9) 3. With the Solar Housing Lid (7) off, gently twist off the Battery Cover (9) with the LED Strip of 12 Bulbs (5) and LED Cover (4) assembly. Move the Battery Cover aside, being careful not to disturb the wires and the internal components. See Figure 2. 4. Removed the dead batteries and dispose of them or recycle them properly according to the Solid Waste Disposal regulations. Replace with new Rechargeable Batteries. The polarity of the batteries is marked. Be careful of the internal components and do not disturb the wires. See Figure 2. 5. Once the batteries are in place, return the Solar Housing Lid (7) and twist clockwise onto the Light Cover (3). Tighten. Led Cover (4) Figure 1 SKU 94740 for technical questions, please call 1-800-444-3353. Page 5 AdApter storAge compArtment 1. Remove the Protective Cover (16) from the bottom of the Solar Lantern by pulling down. Set th...