Votos - 4, Puntuación media: 3.8
(
)
)
|
Resumen del manual
Clean with a dry brush. Be careful not to damage the electric grid. Keep the Solar Panel clear of dirt and dust with a damp cloth. Inspect periodically. People with pacemakers should consult their physician (s) before using this product. Electromagnetic fields in close proximity to a heart pacemaker could cause interference to or failure of the pacemaker. Unpacking When unpacking, check to make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. Assembly Instructions Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual on page 8. Installation Operation Note: The Solar Insect Killer with Light can be configured in two designs. One design is as a Light that resembles a Lantern. The other design is a Solar Garden Light with a stake that goes into the ground. As a Solar Garden Light, insert the assembled Stake (17, 18, 19, & 20) into a flat and level surface. Choose an area where the sunlight falls directly onto the Solar Panel (2). Insert the sharp end of the Stake into the ground, deep enough to hold firmly. Be sure you have avoided any underground wiring or plumbing. Attach the Light firmly on the top of the Stake. See the cover photo. Make sure the area is not accessible to children or pets and that the area has no plant debris nearby that can fall on the unit. As a Lantern design, remove the Stake. You need to place the lantern in a area where the Solar Panel (2) can be charged with direct sunlight while hanging. Lift the Hook (1) and connect it to a chain or hook from a beam or door jam. Avoid hanging it too low where bodily injury could happen. See Figure 3. Figure 1Solar Panel (2) You need to flip the Switch to OFF (8) and charge the Solar Insect Killer with Light when using it for the first time. Charge time for the Solar Panel (2) is at least 2-3 days. After this, it will last eight hours without sunlight. Turn off the light during daylight. Note: The Solar Insect Killer with Light can also be charged with an AC/DC adapter, 4.5V/250mA (not included). Note: There are three positions on the Switch (8). ON, OFF & Ultraviolet Light (that attracts insects to kill them). The Insect Killer position of the switch will operate 6 hours at a time after a full days charge. See Figure 2. Figure 2On/Off and Ultravio- let Switch (8) The power Switch (8) is located on the underside of the top cover. See Figure 2. Hook (1) Lantern StyleGround Stake (17, 18, 19, 20) Figure 3Place the lantern assembly on the top of the Ground Stake (17,18,19, 20). Be sure it is connected firmly. Turn the Switch (8) on. Replacing the batteries Note: If the light stops working after being used for a period of time, it may mean the battery is beyond its lifespan. Remove the Light from the Stake. From the underside of the Light, remove the cage to access the batteries. Twist the cage counterclockwise and lift off to expose the Screws (10). Set aside. (Caution: The cage is fragile. Handle carefully). See Figures 4 & 5. On/off Switch (8) Figure 4Underside of top coverWith a screwdriver (not provided) remove the Screws (10) to expose the batteries. Tilt the Transparent Inner Hood assembly (12), containing the bulbs, carefully aside but still connected. Remove the batteries, being careful not to damage the wiring. See Figures 4 (above) and 5 on page 6. Figure 5Transparent Inner Hood Assembly (12)Batteries (11) Battery Case (9) Replace the dead batteries with identical AA NiCd Rechargeable Batteries (11). Be sure to follow the polarity signs inside of the Battery Case (9). Reverse these steps and reassembly the Solar Insect Killer with Light. Tighten the screws and replace the cage, turning clockwise. Connect assembly to the Stake. Turn the Switch to ON. If it does not light, check to polarity of the batteries again or place the Solar Light in sunlight and charge. Dispose of the used batteries properly by contacting your local community waste disposal facility. INSPECTION, MAINTENANCE, AND CLEANING To remove dust, be sure the Switch is in the OFF position. Use a damp cloth. Dry with a cloth. This product is weather resistant but avoid standing water. Brush off the dried bugs with the Light in the OFF position. PARTS LIST PartDescriptionQ’ty1Hook12Solar Panel13Top Cover14Circuit Board15LED 1 White2 Ultraviolet6Control Circuit Board17Recharge Socket18Switch19Battery Case110Screw4PartDescriptionQ’ty11Battery212Electric Grid113Screw214Reflect Ring115Reflect Board116Outer Hood117Upper Shaft118Connector119Lower Shaft120Ground Stake 1PLEASE READ THE FOLLOWING CAREFULLY The manufacturer and/or distributor has provided the parts list and assem- bly diagram in this manual as a reference tool only. Neither the manufacturer or distributor makes any representation or warranty of any kind to the buyer that he or she is qualified to make any rep...