Votos - 1, Puntuación media: 5
(
)
)
|
Resumen del manual
Tub Installation Instructions 0153/0155 Series Introduction: Thank you for selecting our products...products which have been the benchmarks of fine quality for years. To help insure that the installation process will proceed smoothly, please read these instructions carefully before you begin. Also, review the recommended tools and materials list; carefully unpack and examine your new plumbing fixture. Recommended Tools & Materials Observe Local Plumbing and Building Codes Adjustable Wrench Regular Screwdriver 10' Pipe Wrench Putty Knife Tape Measure Hacksaw Level Roofing Nails (Drain Assembly and Fitting Purchased Separately) Plumbers' Putty or Caulking Vice Grips Teflon Tape Hammer 762mm (30) 1524mm (60) 19mm (3/4) 19mm (3/4) 365mm (14-3/8) 197mm (7-3/4) 13mm (1/2) 305mm (12) 102 (4) 102 (4) 102mm (8) 356mm (14) 229 x 305mm (9 x 12") CUTOUT FINISHED WALL 1-1/2 N.P.T.M. THREADS 1-1/2 O.D. TAILPIECE C/L OF VALVES (44mm [1-3/4"] DIA. HOLES) SPOUT 1/2" S.P.S. ROUGH FLOOR PLUMBER NOTE: PROVIDE SUITABLE FULL LENGTH SUPPORT AT THIS POINT. OPTIONAL TO FINISHED TO FINISHED FLOOR (USUALLY BETWEEN 1651 to 1981mm ( 65" & 78') C/L OF SHOWER CURTAIN ROD (USUALLY 1930mm (76") FROM FIN. FLOOR) 1/2 S.P.S. OR 1/2" C.W.T. SUPPLIES FINISHED WALL FINISHED WALL C/L OF DRAIN SHOWER 1/2" S.P.S. NOTE: NO CONCEALED PIPING FURNISHED SUMP PAD LEFT HAND TUB IS ILLUSTRATED. RIGHT HAND TUB IS REVERSED. *DIMENSION SHOWN FOR OUTLET IS SUGGESTED * 711mm (28) 203mm (8) 76mm (3) 57mm (2-1/4) Roughing-in Dimensions Product names listed herein are trademarks of American Standard Inc. 791116-100 Rev. F 1 1 3 Framing Instructions Note that the typical recess is 1527 x 813mm (60 1/8 x 32”). 229 x 305mm (9 x 12”) hole in sub floor for drain, centered 365mm (14 3/8) as shown. Locate studs as required, then ensure rough opening dimensions are proper and supports are plumb and square. Install 51 x 102mm (2 x 4") stringer, as shown (356mm [14”] off floor). Position bathtub within the recess, check level, front to back, side to side. Also check drain clearance hole in sub floor. To secure the tub, use roofing nails immediately above the rear flange of the tub. Caution: Take extra care when driving nails to avoid damaging the tub. The tile or similar finished floor will be butted against the bottom of the tub apron also holding the tub in place. 1527mm (60-1/8) 762mm(30) 365mm(14-3/8) 813mm(32) TYP. 14 TUB WIDTH LEVELED SUPPORT STRINGER AMERICANSTANDARD NAIL FINISHED TILE FLOOR UNDERLAYMENT SUB FLOOR 2 Install the overflow and drain assembly onto the tub per manufacturer's instructions. Be certain to apply a bead of putty on the underside of drain (part "A") in order to ensure a water tight seal between the tub and drain. Remove excess putty after installing drain on tub. 4 AMERICANSTANDARD A At right is a cross section of the tub rim showing typical wall construction. 51 x 102mm (2 x 4) WOOD STRINGER FULL LENGTH STUD SHIM DRY WALL TILE SEALANT TUB ROOFING NAIL AMERICAN-STANDARD ONE-YEAR LIMI...
Otros modelos de este manual:Otros accesorios para la casa - 153 (1.03 mb)