Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
40" to 54" SHOWER ONLY OPTIONAL 1/2" I.P.S. 1 7-5/8" BOTTOM OF SHOWER OPTIONAL TO FINISHED FLOOR USUALLY BETWEEN 65'' AND 78'' "SEE ILLUSTRATION" 8" REF. COLD HOT 1 5 4 32 1ROUGHING-IN Turn off water at main supply. CAUTION When soldering, remove PLASTER GUARD, CARTRIDGES and CHECK STOPS (IF PRESENT). When finished soldering, flush valve body, replace cartridges, check stops (if present) and plaster guard to continue installation. Use thread sealant or Teflon tape on threaded connections. NOTE Connect hot and cold water supplies. Cap off shower pipe (4). For support, use pipe BRACES (5) secured to wooden braces. With valve turned off, turn on water supplies. Check for leaks. If the valve is installed on a fiberglass or other thin wall application, the PLASTER GUARD (3) can be used as a support. Cut a 4" dia. hole in the shower stall. Drill two additional 1" holes to allow access to the stops. Remove PLASTER GUARD (3), rotate 90° so that indicated screw holes fit MANIFOLD (2). Push CAP on valve, place ESCUTCHEON on and attach with screws. See Roughing-in diagram before starting. Connections are: 1/2" female NPT for threaded inlets Connect RISER PIPE (1) to MANIFOLD (2) top outlet marked "SHR". For proper positioning the finished wall must be within side wall of PLASTER GUARD (3). To assure proper positioning in relation to wall, note roughing-in dimensions. ROUGHING-IN DIMENSIONS Adjustable Wrench Channel Locks Flat Blade Screwdriver Plumbers' Putty or Caulking Phillips Screwdriver Required Tools with EverClean™ Finish Congratulations on purchasing your American Standard faucet with EverClean finish found only on American Standard faucets. To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin. EverClean Finish • One wipe effortlessly removes spots • Eliminates the need for cleaners and scrubbing • Permanent surface protectant remains beautiful for the life of the faucet • EverClean™ available on: Polished Chrome, Satin Nickel, Stainless Steel, Polished Brass (or any combination of these finishes) PRESSURE BALANCING SHOWER SET ................................ Certified to comply with ANSI A112.18.1 InstallationInstructionsTOWNSQUARE 2555.501 THREADED INLETS (STOPS) INLETS 1/2" NPT5-7/8" OUTLETS 1/2" NPT 3-3/8" 1-5/8" TO 3-1/4" FINISHED WALL 74" FOR HEAD CLEARANCE 2" REF. 40" to 54" SHOWER ONLY OPTIONAL 1/2" I.P.S. 1 7-5/8" BOTTOM OF SHOWER OPTIONAL TO FINISHED FLOOR USUALLY BETWEEN 65'' AND 78'' "SEE ILLUSTRATION" 8" REF. COLD HOT 1 5 4 32 1ROUGHING-IN Turn off water at main supply. CAUTION When soldering, remove PLASTER GUARD, CARTRIDGES and CHECK STOPS (IF PRESENT). When finished soldering, flush valve body, replace cartridges, check stops (if present) and plaster guard to continue installation. Use thread sealant or Teflon tape on threaded connections. NOTE Connect hot and cold water supplies. Cap off shower pipe (4). For support, use pipe BRACES (5) secured to wooden braces. With valve turned off, turn on water supplies. Check for leaks. If the valve is installed on a fiberglass or other thin wall application, the PLASTER GUARD (3) can be used as a support. Cut a 4" dia. hole in the shower stall. Drill two additional 1" holes to allow access to the stops. Remove PLASTER GUARD (3), rotate 90° so that indicated screw holes fit MANIFOLD (2). Push CAP on valve, place ESCUTCHEON on and attach with screws. See Roughing-in diagram before starting. Connections are: 1/2" female NPT for threaded inlets Connect RISER PIPE (1) to MANIFOLD (2) top outlet marked "SHR". For proper positioning the finished wall must be within side wall of PLASTER GUARD (3). To assure proper positioning in relation to wall, note roughing-in dimensions. ROUGHING-IN DIMENSIONS Adjustable Wrench Channel Locks Flat Blade Screwdriver Plumbers' Putty or Caulking Phillips Screwdriver Required Tools with EverClean™ Finish Congratulations on purchasing your American Standard faucet with EverClean finish found only on American Standard faucets. To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin. EverClean Finish • One wipe effortlessly removes spots • Eliminates the need for cleaners and scrubbing • Permanent surface protectant remains beautiful for the life of the faucet • EverClean™ available on: Polished Chrome, Satin Nickel, Stainless Steel, Polished Brass (or any combination of these finishes) 3 INSTALL HANDLE ADJUST HOT LIMIT STOP By restricting HANDLE rotation and limiting the amount of hot water allowed to mix with the cold, the HOT LIMIT SAFETY STOP (1) reduces risk of accidental scalding. To set the maximum hot water temperature of your faucet, all you need to do is adjust the setting on the HOT LIMIT SAFETY STOP (1). 151311975310 15131197531 15131197531 4 COLDER (Larger Numbers) 0 1 3 5 7 9 11 13 15 HOTTER (Smaller Numbers) 0 1 3 5 7 9 11 13 15 Turn CARTRIDGE STEM (2) to the OFF position (coldest setting) before making adjustm...