Votos - 3, Puntuación media: 4.3 ( )

Fabricar: Napoleon Fireplaces Tamaño del archivo: 4.99 mb Nombre del archivo: Idioma del manual:

If you smell gas including near the floor, STOP! Follow "B" in the above safety information on this label. If you don't smell gas go to the next step. 6. Find pilot located in front of the back log. A. This fireplace is equipped with a pilot which must be lit by hand while following these instructions exactly. B. Before operating smell all around the fireplace area for gas and next to the floor because some gas is heavier than air and will settle on the floor. C. Use only your hand to push in and turn the gas control knob. Never use tools. If the knob will not push in and turn by hand, do not try to repair it. Call a qualified service technician. Force or attempted repair may result in a fire or explosion. D. Do not use this fireplace if any part has been under water. Immediately call a qualified service technician to inspect the fireplace and replace any part of the control system and any gas control which has been under water. • Do not try to light any appliance. • Do not touch any electric switch; do not use any phone in your building. • Immediately call your gas supplier from a neighbour's phone. Follow the gas supplier's instructions. • If you cannot reach your gas supplier, call the fire department. WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE. oxygen depletion sensor gas knob P I NO LOT FF O 7. Turn gas knob counter-clockwise to pilot. 8. Depress and hold gas knob while lighting the pilot with the push button igniter. Keep knob fully depressed for one minute, then release. If pilot does not continue to burn repeat steps 3 through 7. 9. With pilot lit, turn gas knob counter-clockwise to on. When the pilot has been turned off, ignition of the main burner may be delayed from 1-2 minutes. When the pilot has been left burning, ignition of the main burner should occur almost immediatley. 10. If equipped with remote on-off switch, main burner may not come on when you turn the valve to on. Remote switch must be in the on position to ignite burner. 11. Turn on all electric power to the fireplace. 1. Turn off all electric power to the fireplace if service is to be performed. 2. Push in gas control knob slightly and turn clock- OT PIL LO IH T PILO NO FF O GAS KNOB AT OFF FOR YOUR SAFETY READ BEFORE LIGHTING: LIGHTING INSTRUCTIONS TO TURN OFF GAS WHAT TO DO IF YOU SMELL GAS: W415-0530 / 12.14.05 10 ." LOGO ." LOGO PHAZERTM logs, exclusive to Napoleon Fireplaces, provide a unique and realistic glowing effect that is different in every installation. These logs are fuel specific. Do not interchange. Refer to the replacement parts list. Failure to follow these log placement instructions may cause sooting. 1. Place the rear log #1 onto the locating studs on the rear log support. 2. Position the holes on the bottom of log #2 onto the pins shown. 3. Position the holes on the bottom of log #3 onto the pins shown, with the charred face forward. 4. Position the holes on the bottom of log #4 onto the pins shown, with the charred face inward. 5. Position the holes on the bottom of #5 on the pin on the left end of log #1 and the pin on the left end of log #2. 6. Place the end of log #6 on the right end of log #1. The fork in the log should straddle the knot on top of the log #2. . Log colours may vary. During the initial use of the fireplace, the colours will become more uniform as colour pigments burn in during the heat activated curing process. Positioning the logs improperly will cause flame impingement and carboning. Blocked burner ports can cause an incorrect flame pattern, carbon deposits and delayed ignition. PHAZERTM logs glow when exposed to direct flame. Use only certified PHAZERTM logs available from your Napoleon dealer. LOG PLACEMENT LOGO PLACEMENT Remove the backing of the logo supplied. Centre the logo on the front of the appliance, .” in from the left side, as shown. WARNING Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this heater may result in property damage or personal injury. W415-0530 / 12.14.05 11 1. Place lava or ember rock around the base of the appliance, making sure not to block any burner ports or valve access. Retain a small amount of lava rock for step 3 and if applicable step 4. 2. Place formed charcoal lumps around the front and sides of the unit. 3. Use remaining lava or ember rock to blend with the charcoal lumps. FINISHING GVFL24 GVFL30 GVFL18 4. GVFL30 ONLY: Sprinkle remaining lava rock onto the outer fibre ember beds to hide the seam. RATING PLATE THE RATING PLATE IS CHAINED TO THE PIEZO IGNITOR BRACKET AND SHOULD BE TUCKED UNDER THE ENTIRE ASSEMBLY. 1. Place lava or ember rock around the base of the appliance, making sure not to block any burner ports or valve access. Retain a small amount of lava rock for step 3 and if applicable step 4. 2. Place formed charcoal lumps around the front and sides of the unit. 3. Use ...

Descargar ahora

Introduzca dos números de la imagen: