Votos - 4, Puntuación media: 3.5 ( )

Fabricar: Jacuzzi Tamaño del archivo: 7.85 mb Nombre del archivo: Idioma del manual:

Please refer to this table for component identification of parts list in all Ristorre shower towers. Common Parts List INSTALLATION IMPORTANT: Read all instructions before beginning installation. Consult local codes for requirements. Each unit arrives ready for installation, completely equipped with plumbing and fittings. Remove the unit from the carton. Retain the shipping carton until satisfactory inspection of the product has been made. CAUTION: Do not drop the shower tower. Dropping the unit may damage its appearance and function. Immediately upon receipt, inspect the unit before installing. Should inspection reveal any damage or defect in the finish, do not install. Damage or defect to the finish claimed after the unit is installed is excluded from the warranty. Jacuzzi Whirlpool Bath's responsibility for shipping damage ceases upon delivery of the products in good order to the carrier. Refer any claims for damage to the carrier. For definitions of warranty coverage and limitations, refer NOTE: Parts with item number listed are included. Determine the installation height of the shower tower. The height of the top row of the body jets should be level with the users’ shoulders. Place a mark on the wall at the top of the unit when the top jets are at the desired position. Begin installation using the following instructions. Finish Wall Preparation 1. Drill three holes 1/4" diameter by 1-3/8” deep in the wall at the locations and dimensions shown in Figure 1. 2. Insert plastic anchors (18) into each of the holes, then mount the wall mount fixing rods (7) to the wall using the M4.2x35mm screws (8), see Figure 2. NOTE: Figure 3 is for Metallo only. 3. The User can adjust the height. Drill four holes at 1/4" diameter by 1-3/8" deep. The distance of the holes are 1-3/16" and 35-3/16" apart. Insert the anchor (18) to the holes. Then use the screw (8) to fix the location of the hanger on the wall, see Figure 3. Figure 1 Ovale Onda - - - - - - - - - - - - - - - - - A 5-1/8 7-3/16 B 2-3/8 4-1/2 C 33-1/4 46-1/2 D 3-1/2 2-1/4 - - - - - - - - - - - - - - - - - Measurements in inches Figure 2 Figure 3 1-3/16" 18 8 35-3/16" 1-3/16" 7 35" 1-3/16" Assemble and Install the Shower Tower 1. Attach the shower arm and prepare the glass shampoo platform as follows. a. Attach the shower arm (4) to the front plate (1) with screw nut (11), see Figure 4. Confirm the screen washer at the water inlet fitting of the wall mount shower head (3) is in place and screw the shower head onto the shower arm by hand. Finally, place a sealing washer (21) into the end connector of the flexible tubing as shown in the Figure, and fasten the tubing connector to the shower arm. b. Prepare the glass shampoo platform (14) for assembly to the front plate (1), see Figure 5. Insert the rings (27) and rubber washer (24) into the threaded end of the pillar of the glass shampoo platform (14). c. Attach the glass shampoo platform (14) onto the front plate using the washer plates (25), spring washers (24), and brass nuts (23) to fasten the assembly. d. Place a sealing washer (21) into the hexagon nut of the S.S. flexible hose (16), then, attach the hose onto the threaded connector (22) at the bottom of the back housing (5), see Figure 6. NOTE: There are five sealing washers (21). One is for use in the hexagon nut of the S.S. flexible hose, another is used for the hand shower. The remaining three sealing washers are spare parts to be stored for later use. NOTE: Flush the water lines supply lines to eliminate any construction debris prior to connecting water lines. Ensure there is no particle contamination on the threaded ends of the water supply pipe. Debris and particles in the water supply will reduce shower performance. Figure 4 1 4 11 3 1 21 Parts List The parts list table common to all Ristorre shower towers is located on Page 9. Please refer to this table for component identification of parts list in all Ristorre shower towers. Figure 5 26 Mirror Installation 27 14 25 23 24 Figure 6 21 5 22 16 22 2. Connect 1/2" hoses from the front plate (1) marked in red and blue to the hot and cold water supply’s, respectively, as shown in Figure 7. NOTE: Do not bend or kink the hoses when installing. Tighten fittings with a wrench and test for leaks. 3. Align the three mounting holes of the back housing (5) and front plate (1) with the three mounting rods (7) on wall. Fasten the front plate to the fixing rods and attach with the washers (9) and cap screws (10) provided. NOTE: Figure 8 shows the hot and cold supply locations. BLUE HOSERED HOSEHOT WATER SUPPLYCOLD WATER SUPPLY Figure 7 RED AND BLUE WATER SUPPLY LINES (1/2" NPT Thread) 7 5 5 10 7 9 9 10 7 Onda Ovale Metallo Figure 8 Place supply lines within hatched region Place supply lines within hatched region Place supply lines within hatched region 6.25" 2.00" 2.00" 6.25" 6.25" 3.50" 11.00" 18.50" 4. Using the dimensions indicated in Figure 9, drill two holes 1/4” diameter by 1-3/8” deep into the wall on the right...

Descargar ahora

Introduzca dos números de la imagen: