Votos - 4, Puntuación media: 4.8 ( )

Fabricar: Cal Spas Tamaño del archivo: 5.05 mb Nombre del archivo: Idioma del manual:

(Displays on third occurrence of dr message.) Spa is shut down. Follow action required for dr message. Spa will not automatically reset; you may press any button to reset. Pr When your spa is first actuated, it will go into priming mode. The priming mode will last for up to four minutes and then the spa will begin to heat and maintain the water temperature in the Standard mode. --F or --C Temperature unknown After the pump has been running for two minutes, the temperature will be displayed. - - - - - - Economy or Sleep mode. Temperature not displayed. In Economy or Sleep mode, the pump may be off for hours outside a filter cycle. If you wish to see the current spa temperature, either switch to Standard mode or turn Jets1 on for at least two minutes. BUF Internal problem detected. Repair required. Contact your dealer or service organization. Stby Pressing a button combination on the user panel has activated Standby Mode. Press any button to leave Standby Mode and return to normal operation. SF Safety Suction. Spa is shut down. The display will show SF when a vacuum switch closes. All functions will turn off and the system will be disabled until a panel button is pressed. ST Indicates heater is in Standard Mode. None. Ec Indicates heater is in Economy Mode. None. SL Indicates heater is in Sleep Mode. None. Auxiliary Control Operation The auxiliary control option is available with the 9800 controls only. It is a small panel with four buttons that control certain spa functions, such as primary or additional jets, TV, or lights. It conveniently puts the control of several spa functions at your fingertips without having to get up. For operation, see the previous section, “9800 Electric Control Operation”. Auxiliary Panel Configuration Functions Standard configuration JETS 1, JETS 2, LIGHT, OPTION Spa models with automatic TV JETS 1, JETS 2, TV, OPTION Spa models with 3-pump system JETS 1, JETS 2, JETS 3, OPTION Wireless Spa Monitor The wireless spa monitor allows you to monitor and change your spa’s activity from a distance. The table below describes each button’s function. Light Operates spa light and LED mood lighting Temp Display or adjust the set temperature control Jet 1 Turn on or off jet 1 Mode Switch between Standard, Economy, and Sleep Modes Adjustable Jets Almost all of the jets in your spa are adjustable. Rotating the face of an adjustable jet to the left (counter- clockwise) will decrease the amount of water flow through the jet. Rotating the face of an adjustable jet to the right (clockwise) will increase the amount of water flow through the jet. (See example shown below.) Neck jets adjust in the opposite directions (counter- clockwise to increase, clockwise to decrease). Diverter Knobs Diverter knobs are 1” and 2” knobs located around the top of your spa. They allow you to divert water through jets from one side of the spa to the other, or in most cases from floor jets to wall jets. This is accomplished by rotating the diverter knob to the left (counterclockwise), decreasing the amount of water flow through a section of jets. To increase the amount of water flow through the other section of jets, rotate the handle to the right (clockwise). Air Venturis Air venturis are the 1” knobs located around the top of your spa. Each one will let you add a mixture of air with the jet pressure. This is accomplished by rotating the air venturi knob to the left (counterclockwise) to increase the amount of airflow through the jets. To decrease the amount of airflow through the jets, rotate the handle to the right (clockwise). Adjustable Therapy System™ Pump On/Off This button allows the user to turn on and off the ATS™ seat pump. Press this button once to turn the pump on. Once on, the green LED light on the control panel will illuminate, indicating that the system is operational. To turn off the pump, press the “PUMP ON/OFF” button a second time. Note: The pump must be on prior to operating any other features of this system. Pulse Mode This button allows the user to turn the ATS™ massage control on and off. Press the pulse button once to turn on the massage control. Once pressed, the orange LED in position number 1will light, indicating the number one pulse mode. Each press of either the up or down button will move the orange LED up or down to the next pulse mode. Note: Allow one second between each button press. Pressing the button quickly may cause improper operation. To turn the pulse mode off and return to normal pump operation, press the “PULSE MODE” button a second time. Up This button allows the user to cycle up from one through seven massage modes one at a time. Each mode offers a different pulsating massage. Some modes are faster than others, so just cycle through them to find the massage you like best. Down This button allows the user to cycle down through all seven massage modes, one at a time. Time Reset Mode Pulse mode will normally run for 15 minutes then automatically shut off. For another 15-minute...

Descargar ahora

Introduzca dos números de la imagen: