Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
B. The underwater light can be used for night operation (see USING THE CONTROLS on page 12). The spa includes both red and blue covers for the light. C. The temperature probe monitors water temperature. D. The volcano jet provides a soothing foot massage. E. The whirlpool jet diverts the water flow four ways. Turn the outer ring clockwise or counterclockwise until the ring stops and you hear a click. With each click, the water flow is diverted as follows: to seat 3, and the jet labeled D; next, to the seats labeled 1, 4, 5, and 6; next, to the whirlpool jet; and then to all the jets and seats. Note: The outer ring may be hard to turn while the pump is turned on high. F. The two suction covers provide water to the pump. Never operate the spa without the suction covers in place over the fittings. G. The ozone jet provides ozone sanitation to the spa. The ozone generator engages during the spa’s filtration cycles to destroy algae, viruses, and bacteria while breaking down chemicals and solids for easy removal by the filtration system. Ozone oxidizes combined chlorine and bromine, freeing them to be continuously re-used, reducing the chemical needs and costs of the spa’s sanitation. H. The console controls the spa jets, turns the underwater light on and off, and adjusts the water temperature setting (see USING THE CONTROLS on page 12). I. The three air controls regulate the air flow to the hydrotherapy jets. J. The four neck jets can be adjusted to spray soothing water on your neck. K. The nine rotary jets provide a spinning massage. L. The six dual rotary jets provide a pulsating massage action. Rotate the outer ring counterclockwise to turn the jets on. Rotate the outer ring clockwise to turn the jets off. The jets labeled L1 are always on regardless of the position of the whirlpool jet (E). M. The two power massage jets provides a soothing massage to your lower back. Turn the outer ring to regulate the flow. N. The four adjustable, directional jets can be pivoted to direct their water flow. To open the jets, turn the outer rings counterclockwise; to close the jets, turn the outer rings clockwise. If no air flows through the jets, turn the jets counterclockwise. Close the jets to increase the water pressure to other jets. O. The skimmer cleans the surface of the water. 11 Using the Controls Air Controls Temp Down Temp Up Pump Button Light Button Display Refer to the diagram above. The function of each control is explained below: Temperature Buttons: Control the temperature setting of the water. The temperature can be set from 80°F to 104°F. The water heats at about 6°F per hour with the cover on. Use a medical or other accurate thermometer to check the temperature of the water. To change the water temperature, push either the temp up or temp down button until the desired temperature is reached. If the letters OH, FL, or Sn appear in the display, refer to page 17. Pump Button: Turns the spa jets on and off. This is a two-speed button. If the button is pressed once, the spa jets will run at low speed, providing gentle hydrotherapy. If the button is pressed twice, the spa jets will run at high speed, providing moderate-pressure hydrotherapy. If the button is pressed again, the jets will shut off. The spa also features an automatic mode that heats and filters the water when the spa is left unattended. When the power to the spa is first turned on, or if the water temperature is below the set temperature, the water will be heated as required to maintain the set temperature. Note: To keep the filter and heat cycles from running, the power to the spa must be turned off. Light Button: Turns the underwater light on and off. Air Controls: Determine the amount of air flowing through the spa jets. If a control is turned counterclockwise, the amount of air flowing through the jets will increase; if a control is turned clockwise, the amount of air will decrease. Test each of the air controls to determine which jets are controlled by which air control. 12 Maintenance The hydrotherapy spa is designed to provide years of enjoyment. Please follow the guidelines below to properly maintain your spa. MAINTENANCE SCHEDULE Daily • Check the water level and refill the spa to the level shown in step 4 on page 9. • Check the pH balance and sanitizer level. Adjust if necessary (see WATER CHEMISTRY on page 14). Weekly • Clean the spa shell at the waterline. • Check and thoroughly clean the filter (see CHECKING AND CLEANING THE FILTER CARTRIDGE on this page). • Replace the filter cartridge if needed (see ORDERING REPLACEMENT PARTS on the back cover). Monthly • Clean the spa cover (see MAINTAINING THE SPA COVER on this page). • Soak the filter for two hours in a trisodium phosphate (TSP) solution. Rinse the filter in clean water. • Replace the filter if needed (see ORDERING REPLACEMENT PARTS on the back cover). Every Three Months • Drain the spa and refill it with clean water. Sanitize and test the pH of the water. • Check for any leaks ar...
Otros modelos de este manual:Otros accesorios para la casa - IMSB62820 (486.81 kb)