Votos - 1, Puntuación media: 4
(
)
)
|
Resumen del manual
Side Roof Trim Lt. Side Roof Trim Side Roof Trim Ridge Cap Ridge Cap Door Track Quantity in Carton 2 2 4 8 2 2 1 1 2 2 12 4 2 2 1 2 2 2 1 2 2 Check List Parts List 8P13 Parts in Carton Two Part Part Quantity Check Number Description in Carton List 5986 2 Rear Wall Angle 10389 Rear Walt Channel 2 9365 Front Wall Channel 2 6635 Roof Beam Bracket 4 10386 Roof Beam 8 10388 Side Wall Channel 4 10391 Side Wall Angle 4 10387 Side Floor Frame 4 8936 Rear Floor Frame 2 9367 Front Floor Frame 2 9009 Gable Brace 2 9204 Roof Beam Brace 2 8934 Ramp 1 ,m =. Step 1 $O14 The front floor frame is made up of three pieces. The side floor frames and the rear floor frame are made up of two pieces. The holes in these pieces will align when the pieces are positioned with correct amount of overlap. The illustrations below show the proper overall length for the sides, rear and front. Proceed as follows: I Place the front floor frames as shown. Center the ramp, with drain holes facing outside, on top of the two front floor frames. Join the frames by inserting eight screws. 2 Overlap the side floor frames and the rear floor frames as shown. The holes in these pieces will align when the pieces are positioned with correct amount of overlap. See the illustrations below for the proper overall length of the side and rear floor frames. Join the frames by inserting fourlfive bolts into each frame set as shown. 3 Double check the length of each and set these pieces aside for later use. • Parts Needed For ® O 8934 Ramp (1) O 9367 Front Floor Frame (2) Floor Frame Assemblies ® 8938 Rear Floor Frame (2) O 10387 Side Floor Frame (4) 8934 9367 8936 _#_ L____.J _DRAIN ?? ?_ f_ 8934 _ HOLES FACE_:.9 OUTSIDE Front Floor Frame Assembly 119 3/8" 3,0m9367 O 5986Rear Wall Angle (2) Stp2 . Parts Needed For ® .10389RearWa,,Cha.ne,(2) @ Frame Assemblies ® 10388 Side Wall Channel (4) S015 O 10391 SideWall Angle {4) The main frame pieces reinforce the walls. These pieces will later be installed in the center and at the top edge of the side walls and the rear wall. Proceed as follows: 10389 I I RearWaIIChannel 118 1/8" 3,0m 10389 1 Overlap the rear wall channel pieces as shown in the figure and fasten the two pieces together with eight bolts as shown. 10388 o Ilil I Side Wall Channels t57 3/8" 4,0m 2 Make two side wall channels by overlapping the side wall channel pieces as shown. Fasten each set together with eight bolts as shown. 10388 3 Overlap the rear wall angle pieces as shown in the figure and fasten them together with one bolt in the center hole. __3,0m 5986 _ 5986 RearWallAngle 4 Make two side wall angles by overlapping the side wall angle pieces as shown. Fasten each set together with one bolt thru the second large hole from the end of each part. _ o_._Side Wall Angles Rear Wall ChanneI Side Wail Channels 118 1/8" 157 3/8" 3,0m 4,0m (2 Assemblies) 5 Set the assemblies aside. You will use them later. Rear WailAngIe 118 1/8" 3,Om ® Parts Needed For ® O10386RoofBeam(8) Step 3 Roof Beam Assemblies S016 The roof beams join the two gables and support the roof panels. The main roof beam is made up of four pieces overlapped back to back at the center. The left and right roof beam assemblies are made up of two pieces. Hint: These pieces are force-fitted, so you may have to press hard to join them together. 1 Place the end of one roof beam inside a second roof beam sothat the six holes in each piece align. Make four sets of roof beams by repeating this procedure. Do not insert bolts 2 Take two of the pressed-together roof beams and join them as shown to form the main roof beam assembly. Hold the assembly together and fasten with 14 bolts. Build only_one Doubled Beam Assembly. 3 Fasten the other two pressed- together roof beams with eight bolts to make the left and right roof beam assemblies. 4 Set these pieces aside for later assembly. 10386 10386 _-RoofBeam 1593/8" 4,0m Build one Doubled Main Roof Beam Assembly for Peak in Roof 10386 t 10386 10386 159 3/8" 4,0m tt Build two Single Beam 159 3/8" Assemblies for Break in Roof 4,0m ® Parts Needed For • • 6403DoorTrackSplice(1) Step 4 DooTrack Assembly ®936sDoor, ack(21 S017 The door track assembly supports the sliding doors and reinforces the front wail. It is made up of three pieces. 1 Using the door track splice, (painted), join the door track (galvanized) pieces end-to-end as shown. 2 Insert four screws from the under side only. Hint: The holes in the top sideofthe door track assembly are for fastening the gable to the top of the front wail in a later step. NOTE: Door Track Splice (painted part) 6403 ©© 9366 @_ 66242 9366 Long Leg on Top on Bottom 118 1/8" 3m 3 Position door slides onto the legs, from the end of door track assembly, as shown in the end view. NOTE: Fiat side on top, pins and holes must be oriented as shown. 4 Set this piece aside for later use. END VIEW 1!8 1/8" 3m @ Front Floor Assembly (1) ® Parts Needed For o • Side Floor Assembly (2) Step 5 Floor Frame • Rear Floor Assembly (1) S018 you as...
Otros modelos de este manual:Otros accesorios para la casa - OB1014-B (2.08 mb)
Otros accesorios para la casa - CM1014 (2.08 mb)